E1000 driver in Rust for the Intel 82540EP/EM and 82574L Gigabit Ethernet.
e1000ande1000edriver on Qemu and a Physical Industrial Computer are supported- Initialize simple PCI-Express for e1000 device
- Implement the e1000 driver as a linux driver module
- Todo: networking protocol support: IP, ARP, UDP
For instance, E1000 driver in Rust on ArceOS/Starry
Initialize PCI and E1000 driver
pub struct Kernfn;
impl e1000_driver::e1000::KernelFunc for Kernfn { ... }
e1000_driver::pci::pci_init();
let mut e1000_device = e1000_driver::e1000::E1000Device::<Kernfn>::new(e1000_driver::pci::E1000_REGS as usize).unwrap();
Sending network packets
e1000_device.e1000_transmit(&frame);
Receiving network packets
let rx_buf = e1000_device.e1000_recv();
cd src/linux
make ARCH=<cpu arch> KDIR=<path to linux>
# e.g. make ARCH=x86_64 KDIR=/home/rust/linux/build
e1000-driverruns on Linux
- Performance test results on Linux
root@debian:~/xly# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
4: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
inet 10.0.2.10/24 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:fe12:3456/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
root@debian:~/xly# iperf3 -c 192.168.0.250 -p 8880 -b 100M -P 1 -t 5
Connecting to host 192.168.0.250, port 8880
[ 5] local 10.0.2.10 port 50338 connected to 192.168.0.250 port 8880
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 11.9 MBytes 99.4 Mbits/sec 0 177 KBytes
[ 5] 1.00-2.00 sec 12.0 MBytes 101 Mbits/sec 0 177 KBytes
[ 5] 2.00-3.00 sec 11.9 MBytes 99.6 Mbits/sec 0 177 KBytes
[ 5] 3.00-4.00 sec 11.9 MBytes 99.6 Mbits/sec 0 177 KBytes
[ 5] 4.00-5.00 sec 12.0 MBytes 101 Mbits/sec 0 177 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-5.00 sec 59.6 MBytes 100 Mbits/sec 0 sender
[ 5] 0.00-5.00 sec 59.6 MBytes 100 Mbits/sec receiver
iperf Done.
root@debian:~/xly# iperf3 -u -c 192.168.0.250 -p 8880 -b 100M -P 1 -t 5
Connecting to host 192.168.0.250, port 8880
[ 5] local 10.0.2.10 port 44234 connected to 192.168.0.250 port 8880
[ ID] Interval Transfer Bitrate Total Datagrams
[ 5] 0.00-1.00 sec 11.9 MBytes 99.9 Mbits/sec 8556
[ 5] 1.00-2.00 sec 11.9 MBytes 100 Mbits/sec 8562
[ 5] 2.00-3.00 sec 11.9 MBytes 100 Mbits/sec 8562
[ 5] 3.00-4.00 sec 11.9 MBytes 100 Mbits/sec 8562
[ 5] 4.00-5.00 sec 11.9 MBytes 100 Mbits/sec 8561
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-5.00 sec 59.6 MBytes 100 Mbits/sec 0.000 ms 0/42803 (0%) sender
[ 5] 0.00-5.04 sec 59.6 MBytes 99.1 Mbits/sec 0.002 ms 0/42803 (0%) receiver
iperf Done.
root@debian:~/xly# ping 10.0.2.2
PING 10.0.2.2 (10.0.2.2) 56(84) bytes of data.
64 bytes from 10.0.2.2: icmp_seq=1 ttl=255 time=0.149 ms
64 bytes from 10.0.2.2: icmp_seq=2 ttl=255 time=0.256 ms
64 bytes from 10.0.2.2: icmp_seq=3 ttl=255 time=0.193 ms
64 bytes from 10.0.2.2: icmp_seq=4 ttl=255 time=0.190 ms
^C
--- 10.0.2.2 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3054ms
rtt min/avg/max/mdev = 0.149/0.197/0.256/0.038 ms
root@debian:~/xly# lsmod
Module Size Used by
e1000_for_linux 45056 0
root@debian:~/xly# uname -a
L