- Filament type: PETG
- Slicer: PrusaSlicer
- Infill type : Gyroid recommended
- Support : No
- Brim : No
- Detect thin walls : No
- Perimeters width (internal and external) : 0.45mm
| Part | Quantity | Layer Height [mm] |
Infill [%] | Num. Perimeters |
Num. Top / Bottom Layers |
Note |
|---|---|---|---|---|---|---|
| build_helper_y | 1 | 0.20 | 20 | 3 | 5 | |
| build_helper_z | 1 | 0.20 | 20 | 3 | 5 | |
| cable_clip_horizontal | 2 | 0.20 | 20 | 4 | 5 | |
| cable_clip_lcd | 5 | 0.20 | 20 | 4 | 5 | |
| cable_clip_vertical | 6 | 0.20 | 20 | 4 | 5 | |
| foot | 4 | 0.20 | 20 | 3 | 5 | |
| lcd_support_a | 1 | 0.20 | 20 | 3 | 5 | |
| lcd_support_b | 1 | 0.20 | 20 | 3 | 5 | |
| psu_lower_mount | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your PSU version |
| psu_upper_mount | 2 | 0.20 | 20 | 3 | 5 | File name may vary depending your PSU version |
| rambo_base_lower_mount | 1 | 0.20 | 20 | 3 | 5 | |
| rambo_base_upper_mount | 1 | 0.20 | 20 | 3 | 5 | |
| rambo_hinge_lower | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your printer version |
| rambo_hinge_upper | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your printer version |
| y_bearing_holder | 3 | 0.20 | 20 | 5 | 5 | |
| y_belt_holder | 1 | 0.20 | 20 | 4 | 5 | |
| y_end_caps | 2 | 0.20 | 20 | 3 | 5 | Total of 4 printed parts |
| y_idler_mount | 1 | 0.20 | 20 | 4 | 5 | |
| y_idler_tensioner | 1 | 0.20 | 20 | 4 | 5 | |
| y_motor_endstop_mount | 1 | 0.20 | 20 | 4 | 5 | |
| y_motor_mount | 1 | 0.20 | 20 | 4 | 5 | |
| y_rod_holder | 4 | 0.20 | 20 | 4 | 5 | |
| z_end_caps | 1 | 0.20 | 20 | 3 | 5 | Total of 2 printed parts |
| z_leadscrew_cap | 2 | 0.20 | 20 | 2 | 5 | |
| z_motor_mounts | 1 | 0.20 | 20 | 4 | 5 | Total of 2 printed parts |
| z_tops | 1 | 0.20 | 20 | 4 | 5 | Total of 2 printed parts |