mbed.h header file not found

[mbueno0]

I'm using an 'AI-thinker-esque' esp32-cam board. The cam works fine after having selected 'AI-thinker' as my board and trying the generic example for the aforementioned board. I can view the video in my web browser just fine.

I'm trying to get your code to compile after having installed the library and including the files within the Arduino IDE.

I'm getting this error when I try to compile:

In file included from C:\Users\Bueno\Documents\Arduino\myEsp32-camCameraWebServer1_0\myEsp32-camCameraWebServer1_0.ino:8:0:
C:\Users\Bueno\Documents\Arduino\libraries\Micro-RTSP-master\src/platglue-mbed.h:6:18: fatal error: mbed.h: No such file or directory
compilation terminated.
exit status 1
Error compiling for board AI Thinker ESP32-CAM.
Error downloading https://git.oschina.net/dfrobot/FireBeetle-ESP32/raw/master/package_esp32_index.json

Looking at the src code, I see there is no 'mbed.h' header file.

Thanks in advance for any help with which you can provide me !!! :)

Here's my src code in full:

`#include <CRtspSession.h>
#include <CStreamer.h>
#include <JPEGSamples.h>
#include <LinkedListElement.h>
#include <OV2640.h>
#include <OV2640Streamer.h>
#include <platglue-esp32.h>
#include <platglue-mbed.h>
#include <platglue-posix.h>
#include <platglue.h>
#include <SimStreamer.h>

#include "esp_camera.h"
#include <WiFi.h>

//
// WARNING!!! Make sure that you have either selected ESP32 Wrover Module,
// or another board which has PSRAM enabled
//

// Select camera model
//#define CAMERA_MODEL_WROVER_KIT
//#define CAMERA_MODEL_ESP_EYE
//#define CAMERA_MODEL_M5STACK_PSRAM
//#define CAMERA_MODEL_M5STACK_WIDE
#define CAMERA_MODEL_AI_THINKER

#include "camera_pins.h"

// thisIsMyStuff
const char* ssid = "purposelyOmitted";
const char* password = "purposelyOmitted";

//IPAddress local_IP(192, 168, 1, 251);
//IPAddress gateway(192, 168, 1 ,1);
//IPAddress subnet(255, 255, 255, 0);

// Following two settings are optional
//IPAddress primaryDNS(8, 8, 8, 8);
//IPAddress secondaryDNS(8, 8, 4, 4);

//Static IP Config*****/
//IPAddress ap_local_IP(192, 168, 1, 251);
//IPAddress ap_gateway(192,168,1,255);
//IPAddress ap_subnet(255,255,255,0);

// endOfMyStuff
void startCameraServer();

void setup() {
Serial.begin(115200);
Serial.setDebugOutput(true);
Serial.println();

camera_config_t config;
config.ledc_channel = LEDC_CHANNEL_0;
config.ledc_timer = LEDC_TIMER_0;
config.pin_d0 = Y2_GPIO_NUM;
config.pin_d1 = Y3_GPIO_NUM;
config.pin_d2 = Y4_GPIO_NUM;
config.pin_d3 = Y5_GPIO_NUM;
config.pin_d4 = Y6_GPIO_NUM;
config.pin_d5 = Y7_GPIO_NUM;
config.pin_d6 = Y8_GPIO_NUM;
config.pin_d7 = Y9_GPIO_NUM;
config.pin_xclk = XCLK_GPIO_NUM;
config.pin_pclk = PCLK_GPIO_NUM;
config.pin_vsync = VSYNC_GPIO_NUM;
config.pin_href = HREF_GPIO_NUM;
config.pin_sscb_sda = SIOD_GPIO_NUM;
config.pin_sscb_scl = SIOC_GPIO_NUM;
config.pin_pwdn = PWDN_GPIO_NUM;
config.pin_reset = RESET_GPIO_NUM;
config.xclk_freq_hz = 20000000;
config.pixel_format = PIXFORMAT_JPEG;
//init with high specs to pre-allocate larger buffers
if(psramFound()){
config.frame_size = FRAMESIZE_UXGA;
config.jpeg_quality = 10;
config.fb_count = 2;
} else {
config.frame_size = FRAMESIZE_SVGA;
config.jpeg_quality = 12;
config.fb_count = 1;
}

#if defined(CAMERA_MODEL_ESP_EYE)
pinMode(13, INPUT_PULLUP);
pinMode(14, INPUT_PULLUP);
#endif

// camera init
esp_err_t err = esp_camera_init(&config);
if (err != ESP_OK) {
Serial.printf("Camera init failed with error 0x%x", err);
return;
}

sensor_t * s = esp_camera_sensor_get();
//initial sensors are flipped vertically and colors are a bit saturated
if (s->id.PID == OV3660_PID) {
s->set_vflip(s, 1);//flip it back
s->set_brightness(s, 1);//up the blightness just a bit
s->set_saturation(s, -2);//lower the saturation
}
//drop down frame size for higher initial frame rate
s->set_framesize(s, FRAMESIZE_QVGA);

#if defined(CAMERA_MODEL_M5STACK_WIDE)
s->set_vflip(s, 1);
s->set_hmirror(s, 1);
#endif

// thisIsMyStuff
//const char* ssid = "purposelyOmitted";
//const char* password = "purposelyOmitted";

IPAddress local_IP(192, 168, 1, 251);
IPAddress gateway(192, 168, 1 ,1);
IPAddress subnet(255, 255, 255, 0);

// Following two settings are optional
//IPAddress primaryDNS(8, 8, 8, 8);
//IPAddress secondaryDNS(8, 8, 4, 4);

//Static IP Config*****/
//IPAddress ap_local_IP(192, 168, 1, 251);
//IPAddress ap_gateway(192,168,1,255);
//IPAddress ap_subnet(255,255,255,0);

// endOfMyStuff

WiFi.begin(ssid, password);

while (WiFi.status() != WL_CONNECTED) {
delay(500);
Serial.print(".");
}
Serial.println("");
Serial.println("WiFi connected");

startCameraServer();

Serial.print("Camera Ready! Use 'http://");
Serial.print(WiFi.localIP());
Serial.println("' to connect");
}

void loop() {
// put your main code here, to run repeatedly:
delay(10000);
}`

Thanks again !!!

[audas]

Any chance there is a fix for this issue please?