-
Notifications
You must be signed in to change notification settings - Fork 2
/
config.txt
128 lines (96 loc) · 3.46 KB
/
config.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
####################################################
#### MainsailOS specific configurations ####
####################################################
#### DO NOT CHANGE SECTION BELOW !!! ####
#### UNLESS YOU KNOW WHAT YOU ARE DOING !!! ####
####################################################
## For more options and information see
## https://www.raspberrypi.com/documentation/computers/config_txt.html
## Some settings may impact device functionality. See link above for details
## For additional information about device filters see
## https://www.raspberrypi.com/documentation/computers/config_txt.html#model-filters
[pi0]
## This affects Pi Zero(W) and Pi Zero2
## Due lag of RAM, limit GPU RAM
gpu_mem=128
[pi2]
gpu_mem=256
[pi3]
## Use 256 if 1Gb Ram Model!
gpu_mem=128
# gpu_mem=256
[pi4]
## Enable DRM VC4 V3D driver on top of the dispmanx display stack
#dtoverlay=vc4-fkms-v3d
max_framebuffers=2
## Do not use more than 256Mb on Pi Model 4, it uses its own Management.
gpu_mem=256
[all]
## SPI Interface is enabled by default for Input Shaper
## To revert that comment out line #48
## This colides with Hyperpixel Display!
## Hyperpixel Screen uses the same Pin for Backlight.
## Enable Hardware UART for Serial Communication
enable_uart=1
dtoverlay=disable-bt
## Enable VideoCore at boot, needed for Raspicams and DSI devices.
start_x=1
### EXPERIMENTAL - Enable 64bit Kernel
### The 64-bit kernel will only work on:
### Raspberry Pi 3, 3+, 4, 400, Zero 2 W and 2B rev 1.2
### and Raspberry Pi Compute Modules 3, 3+ and 4.
# arm_64bit=1
####################################################
###### MKS TS35
hdmi_force_hotplug=1
hdmi_cvt=320 480 60 5 0 0 0
hdmi_group=2
#hdmi_mode=1
hdmi_mode=87
display_rotate=0x10002
# MKS TS35 Rotated 270 (for fit on Two Trees Bluer)
dtparam=spi=on
dtoverlay=tinylcd35,rotate=0,speed=36000000,touch,touchgpio=23,fps=10