version v3.4.0b8 : RC310 HC1 - missing summertemp ?

[zibous]

Boiler GBx72/Trendline/Cerapur/Greenstar Si/27i   
Thermostat  RC300/RC310/Moduline 3000/1010H/CW400/Sense II

Version: EMS-ESP Version v3.4.0b8

Bug description
With version v3.4.0b8 I don't get the summertemp setting anymore.
Is this based on hc1 summer mode: off?

Version v3.3 shows:

"hc1": {
		"seltemp": 24,
		"temp": 24,
		"hatemp": 24,
		"hamode": "auto",
		"mode": "auto",
		"modetype": "comfort",
		"ecotemp": 15,
		"manualtemp": 24,
		"comforttemp": 25,
		"summertemp": 17,  <----- OK
		"designtemp": 45,
		"offsettemp": 0,
		"minflowtemp": 25,
		"maxflowtemp": 60,
		"roominfluence": 0,
		"curroominfl": 0,
		"nofrosttemp": 5,
		"targetflowtemp": 38,
		"heatingtype": "radiator",
		"summersetmode": "auto",
		"summermode": "off",
		"controlmode": "optimized",
		"program": "prog_1",
		"fastheatup": 0
	}

Device information

{
  "System": {
    "version": "3.4.0b8",
    "uptime": "002+05:57:31.665",
    "uptime (seconds)": 194251,
    "freemem": 149,
    "reset reason": "Software reset CPU / Software reset CPU",
    "temperature sensors": 0,
    "analog sensors": 0
  },
  "Network": {
    "connection": "WiFi",
    ...
  },
  "Status": {
    "bus status": "connected",
    "bus protocol": "Buderus",
    "bus telegrams received (rx)": 190341,
    "bus reads (tx)": 41887,
    "bus writes (tx)": 26,
    "bus incomplete telegrams": 16,
    "bus reads failed": 258,
    "bus writes failed": 0,
    "bus rx line quality": 100,
    "bus tx line quality": 100,
    "MQTT status": "connected",
    "MQTT publishes": 61997,
    "MQTT publish fails": 0,
    "temperature sensors": 0,
    "temperature sensor reads": 0,
    "temperature sensor fails": 0,
    "analog sensors": 0,
    "analog sensor reads": 0,
    "analog sensor fails": 0,
    "API calls": 0,
    "API fails": 0,
    "syslog started": true,
    "syslog level": "debug",
    "syslog ip": "10.1.1.96",
    "syslog queue": 1
  },
  "Devices": [
    {
      "type": "Boiler",
      "name": "GBx72/Trendline/Cerapur/Greenstar Si/27i",
      "device id": "0x08",
      "product id": 123,
      "version": "07.00",
      "entities": 66,
      "handlers received": "0x10 0x11 0x15 0x1C 0x18 0x19 0x1A 0x35 0x34 0x2A",
      "handlers fetched": "0x14 0x16 0x33 0x26",
      "handlers pending": "0xC2 0xD1 0xE3 0xE4 0xE5 0xE6 0xE9 0xEA"
    },
    {
      "type": "Thermostat",
      "name": "RC300/RC310/Moduline 3000/1010H/CW400/Sense II",
      "device id": "0x10",
      "product id": 158,
      "version": "74.02",
      "entities": 32,
      "handlers received": "0x06 0xA2 0x02BA 0x02BB 0x02BC 0x02BD 0x02BE 0x02BF 0x02C0 0x031D 0x0267",
      "handlers fetched": "0x02A5 0x02B9 0x029B 0x02F5 0x031B 0x023A 0x0240",
      "handlers pending": "0xA3 0x12 0x02AF 0x0471 0x02A6 0x02B0 0x029C 0x0472 0x02A7 0x02B1 0x029D 0x0473 0x02A8 0x02B2 0x029E 0x0474 0x02A9 0x02B3 0x029F 0x0475 0x02AA 0x02B4 0x02A0 0x0476 0x02AB 0x02B5 0x02A1 0x0477 0x02AC "
    },
    {
      "type": "Controller",
      "name": "BC25",
      "device id": "0x09",
      "product id": 125,
      "version": "03.05",
      "entities": 0
    }
  ]
}

Additional context

Boiler: Buderus GBx72/Trendline/Cerapur/Greenstar Si/27i (DeviceID:0x08, ProductID:123, Version:07.00) (66)
  heating active: off
  tapwater active: off
  selected flow temperature: 35.0 °C
  burner selected max power: 100 %
  heating pump modulation: 41 %
  outside temperature: 10.5 °C
  current flow temperature: 31.3 °C
  gas: off
  gas stage 2: off
  flame current: 0.0 uA
  heating pump: on
  fan: off
  ignition: off
  oil preheating: off
  heating activated: on
  heating temperature: 60.0 °C
  burner pump max power: 100 %
  burner pump min power: 10 %
  pump delay: 5
  burner min period: 10
  burner min power: 0 %
  burner max power: 100 %
  hysteresis on temperature: -6.0 °C
  hysteresis off temperature: 6.0 °C
  set flow temperature: 35.0 °C
  burner set power: 100 %
  burner current power: 0 %
  burner starts: 5279
  total burner operating time: 76 days 13 hours 44 minutes
  total heat operating time: 69 days 18 hours 46 minutes
  total UBA operating time: 281 days 12 hours 44 minutes
  last error code: 0Y(276) 24.11.2021 03:51 (0 min)
  service code: 0Y
  service code number: 204
  maintenance message: H00
  maintenance scheduled: date
  time to next maintenance: 6000 hours
  next maintenance date: 07.07.2023
  dhw set temperature: 57.0 °C
  dhw selected temperature: 57.0 °C
  dhw type: buffer
  dhw comfort: eco
  dhw flow temperature offset: 40.0 °C
  dhw max power: 100 %
  dhw circulation pump available: off
  dhw charging type: 3-way valve
  dhw hysteresis on temperature: -5.0 °C
  dhw hysteresis off temperature: 0.0 °C
  dhw disinfection temperature: 70.0 °C
  dhw circulation pump mode: 2x3min
  dhw circulation active: off
  dhw current intern temperature: 58.5 °C
  dhw current extern temperature: 58.5 °C
  dhw current tap water flow: 0.0 l/min
  dhw storage extern temperature: 58.5 °C
  dhw activated: on
  dhw one time charging: off
  dhw disinfecting: off
  dhw charging: off
  dhw recharging: off
  dhw temperature ok: on
  dhw active: off
  dhw 3way valve active: off
  dhw set pump power: 0 %
  dhw starts: 1087
  dhw active time: 6 days 18 hours 58 minutes

Thermostat: RC300/RC310/Moduline 3000/1010H/CW400/Sense II (DeviceID:0x10, ProductID:158, Version:74.02) (32)
  date/time: 19:20:18 18.03.2022
  floor drying: off
  damped outdoor temperature: 11.3 °C
  floor drying temperature: 0.0 °C
  building type: light
  minimal external temperature: -10.0 °C
  dhw set temperature: 60.0 °C
  dhw mode: own_prog
  dhw set low temperature: 45.0 °C
  dhw circulation pump mode: own_prog
  dhw charge duration: 60.0
  dhw charge: off
  dhw circuit 1 extra: 0.0 °C
  dhw disinfecting: on
  dhw disinfection day: we
  dhw disinfection time: 180.0
  hc1 selected room temperature: 24.0 °C
  hc1 : selTemp
  hc1 mode: auto
  hc1 mode type: comfort
  hc1 eco temperature: 20.0 °C
  hc1 manual temperature: 24.0 °C
  hc1 comfort temperature: 24.0 °C
  hc1 max flow temperature: 60.0 °C
  hc1 current room influence: 0.0 °C
  hc1 nofrost temperature: 0.0 °C
  hc1 target flow temperature: 35.0 °C
  hc1 heating type: radiator
  hc1 summer mode: off
  hc1 control mode: optimized
  hc1 program: prog_1
  hc1 temporary set temperature automode: 24.0 °C

Controller: BC25 (DeviceID:0x09, ProductID:125, Version:03.05) (0)

[MichaelDvP]

Check Settings->Customization, there are some new values and the list is shifted after update.

But indeed there is a bug, the climate setting with empty fullname should not be displayed in console ( hc1 : selTemp).

[marc1de]

Please check if this value is disabled in "settings -> customisation"
In version v3.4.0b8 the numbering has changed.

(for a more detailed explanation by proddy or MichaelDvP see issue #396)

[zibous]

@marc1de
Thanks, found.

1. Delete HA discovery
2. Restart EMS

Now i can see this in Homeassistant and on the dashboard.

{
  "datetime": "12:05:38 19.03.2022",
  "floordry": "off",
  "dampedoutdoortemp": 9.2,
  "floordrytemp": 0,
  "building": "light",
  "minexttemp": -10,
  "wwsettemp": 60,
  "wwmode": "own_prog",
  "wwsettemplow": 45,
  "wwcircmode": "own_prog",
  "wwchargeduration": 60,
  "wwcharge": "off",
  "wwextra1": 0,
  "wwdisinfecting": "on",
  "wwdisinfectday": "we",
  "wwdisinfecttime": 180,
  "hc1": {
    "seltemp": 24,
    "climate": "selTemp",
    "mode": "auto",
    "modetype": "comfort",
    "ecotemp": 20,
    "manualtemp": 24,
    "comforttemp": 24,
    "summertemp": 15,  <---- OK
    "designtemp": 45,
    "offsettemp": 0,
    "minflowtemp": 25,
    "maxflowtemp": 60,
    "roominfluence": 0,
    "roominflfactor": 4,
    "curroominfl": 0,
    "nofrosttemp": 0,
    "targetflowtemp": 37,
    "heatingtype": "radiator",
    "summersetmode": "auto",
    "summermode": "off",
    "controlmode": "optimized",
    "program": "prog_1",
    "tempautotemp": 24,
    "fastheatup": 0
  }
}

Thanks