-
Notifications
You must be signed in to change notification settings - Fork 2k
/
SanityCheck.h
2513 lines (2339 loc) · 114 KB
/
SanityCheck.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* SanityCheck.h
*
* Test configuration values for errors at compile-time.
*/
/**
* Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features.
*/
#if __cplusplus < 201103L
#error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain."
#endif
/**
* We try our best to include sanity checks for all changed configuration
* directives because users have a tendency to use outdated config files with
* the bleeding-edge source code, but sometimes this is not enough. This check
* forces a minimum config file revision. Otherwise Marlin will not build.
*/
#define HEXIFY(H) _CAT(0x,H)
#if !defined(CONFIGURATION_H_VERSION) || HEXIFY(CONFIGURATION_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_H_VERSION)
#error "You are using an old Configuration.h file, update it before building Marlin."
#endif
#if !defined(CONFIGURATION_ADV_H_VERSION) || HEXIFY(CONFIGURATION_ADV_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_ADV_H_VERSION)
#error "You are using an old Configuration_adv.h file, update it before building Marlin."
#endif
#undef HEXIFY
/**
* Warnings for old configurations
*/
#ifndef MOTHERBOARD
#error "MOTHERBOARD is required. Please update your configuration."
#elif !defined(X_BED_SIZE) || !defined(Y_BED_SIZE)
#error "X_BED_SIZE and Y_BED_SIZE are now required! Please update your configuration."
#elif WATCH_TEMP_PERIOD > 500
#error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
#elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
#error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
#elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
#error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
#elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE)
#error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY."
#elif defined(X_HOME_RETRACT_MM)
#error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
#elif defined(SDCARDDETECTINVERTED)
#error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
#elif defined(BTENABLED)
#error "BTENABLED is now BLUETOOTH. Please update your configuration."
#elif defined(CUSTOM_MENDEL_NAME)
#error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
#elif defined(HAS_AUTOMATIC_VERSIONING)
#error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
#elif defined(SDSLOW)
#error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
#elif defined(SDEXTRASLOW)
#error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
#elif defined(FILAMENT_SENSOR)
#error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR. Please update your configuration."
#elif defined(ENDSTOPPULLUP_FIL_RUNOUT)
#error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP. Please update your configuration."
#elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
#error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
#elif defined(LANGUAGE_INCLUDE)
#error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
#elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
#error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
#elif defined(PID_PARAMS_PER_EXTRUDER)
#error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
#elif defined(EXTRUDER_WATTS) || defined(BED_WATTS)
#error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration."
#elif defined(SERVO_ENDSTOP_ANGLES)
#error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
#elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
#error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
#elif defined(Z_ENDSTOP_SERVO_NR)
#error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR. Please update your configuration."
#elif defined(DEFAULT_XYJERK)
#error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead."
#elif defined(XY_TRAVEL_SPEED)
#error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
#elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
#error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
#elif defined(SERVO_DEACTIVATION_DELAY)
#error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
#elif ENABLED(FILAMENTCHANGEENABLE)
#error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
#elif ENABLED(FILAMENT_CHANGE_FEATURE)
#error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
#elif defined(FILAMENT_CHANGE_X_POS) || defined(FILAMENT_CHANGE_Y_POS)
#error "FILAMENT_CHANGE_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#elif defined(FILAMENT_CHANGE_Z_ADD)
#error "FILAMENT_CHANGE_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration."
#elif defined(FILAMENT_CHANGE_XY_FEEDRATE)
#error "FILAMENT_CHANGE_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration."
#elif defined(FILAMENT_CHANGE_Z_FEEDRATE)
#error "FILAMENT_CHANGE_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration."
#elif defined(PAUSE_PARK_X_POS) || defined(PAUSE_PARK_Y_POS)
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#elif defined(PAUSE_PARK_Z_ADD)
#error "PAUSE_PARK_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration."
#elif defined(PAUSE_PARK_XY_FEEDRATE)
#error "PAUSE_PARK_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration."
#elif defined(PAUSE_PARK_Z_FEEDRATE)
#error "PAUSE_PARK_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration."
#elif defined(FILAMENT_CHANGE_RETRACT_FEEDRATE)
#error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE. Please update your configuration."
#elif defined(FILAMENT_CHANGE_RETRACT_LENGTH)
#error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH. Please update your configuration."
#elif defined(FILAMENT_CHANGE_EXTRUDE_FEEDRATE)
#error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration."
#elif defined(ADVANCED_PAUSE_EXTRUDE_FEEDRATE)
#error "ADVANCED_PAUSE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration."
#elif defined(FILAMENT_CHANGE_EXTRUDE_LENGTH)
#error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration."
#elif defined(ADVANCED_PAUSE_EXTRUDE_LENGTH)
#error "ADVANCED_PAUSE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration."
#elif defined(FILAMENT_CHANGE_NOZZLE_TIMEOUT)
#error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT. Please update your configuration."
#elif defined(FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS)
#error "FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS is now FILAMENT_CHANGE_ALERT_BEEPS. Please update your configuration."
#elif defined(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT)
#error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT. Please update your configuration."
#elif defined(PLA_PREHEAT_HOTEND_TEMP)
#error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
#elif defined(PLA_PREHEAT_HPB_TEMP)
#error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
#elif defined(PLA_PREHEAT_FAN_SPEED)
#error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
#elif defined(ABS_PREHEAT_HOTEND_TEMP)
#error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
#elif defined(ABS_PREHEAT_HPB_TEMP)
#error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
#elif defined(ABS_PREHEAT_FAN_SPEED)
#error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
#elif defined(ENDSTOPS_ONLY_FOR_HOMING)
#error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
#elif defined(HOMING_FEEDRATE)
#error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
#elif defined(MANUAL_HOME_POSITIONS)
#error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
#elif defined(PID_ADD_EXTRUSION_RATE)
#error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
#elif defined(Z_RAISE_BEFORE_HOMING)
#error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
#elif defined(MIN_Z_HEIGHT_FOR_HOMING)
#error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
#elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
#error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead."
#elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
#error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
#elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
#error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
#elif defined(MANUAL_BED_LEVELING)
#error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING. Please update your configuration."
#elif defined(MESH_HOME_SEARCH_Z)
#error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE. Please update your configuration."
#elif defined(MANUAL_PROBE_Z_RANGE)
#error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE. Please update your configuration."
#elif !defined(MIN_STEPS_PER_SEGMENT)
#error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
#elif MIN_STEPS_PER_SEGMENT <= 0
#error "MIN_STEPS_PER_SEGMENT must be at least 1. Please update your Configuration_adv.h."
#elif defined(PREVENT_DANGEROUS_EXTRUDE)
#error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
#elif defined(SCARA)
#error "SCARA is now MORGAN_SCARA. Please update your configuration."
#elif defined(ENABLE_AUTO_BED_LEVELING)
#error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
#elif defined(AUTO_BED_LEVELING_FEATURE)
#error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
#elif defined(ABL_GRID_POINTS)
#error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y. Please update your configuration."
#elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y)
#error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
#elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y)
#error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
#elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS)
#error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
#elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS)
#error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
#elif defined(UBL_G26_MESH_VALIDATION)
#error "UBL_G26_MESH_VALIDATION is now G26_MESH_VALIDATION. Please update your configuration."
#elif defined(UBL_MESH_EDIT_ENABLED)
#error "UBL_MESH_EDIT_ENABLED is now G26_MESH_VALIDATION. Please update your configuration."
#elif defined(UBL_MESH_EDITING)
#error "UBL_MESH_EDITING is now G26_MESH_VALIDATION. Please update your configuration."
#elif defined(BLTOUCH_HEATERS_OFF)
#error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF. Please update your configuration."
#elif defined(BLTOUCH_V3)
#error "BLTOUCH_V3 is obsolete. Please update your configuration."
#elif defined(BLTOUCH_FORCE_OPEN_DRAIN_MODE)
#error "BLTOUCH_FORCE_OPEN_DRAIN_MODE is obsolete. Please update your configuration."
#elif defined(BEEPER)
#error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
#elif defined(SDCARDDETECT)
#error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
#elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE)
#error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN. Please update your pins definitions."
#elif defined(LCD_PIN_BL)
#error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions."
#elif defined(LCD_PIN_RESET)
#error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions."
#elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN)
#error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
#elif defined(min_software_endstops) || defined(max_software_endstops)
#error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration."
#elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN)
#error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
#elif defined(CONTROLLERFAN_PIN)
#error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h."
#elif defined(MIN_RETRACT)
#error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
#elif defined(ADVANCE)
#error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
#elif defined(LIN_ADVANCE_E_D_RATIO)
#error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO. Check your configuration."
#elif defined(NEOPIXEL_RGBW_LED)
#error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
#elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS)
#error "Remove DELTA_PROBEABLE_RADIUS and use MIN_PROBE_EDGE to inset the probe area instead."
#elif defined(UBL_MESH_INSET)
#error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
#elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y)
#error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
#elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y)
#error "ABL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
#elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y)
#error "UBL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
#elif defined(LEFT_PROBE_BED_POSITION)
#error "LEFT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_LEFT. Please update your configuration."
#elif defined(RIGHT_PROBE_BED_POSITION)
#error "RIGHT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_RIGHT. Please update your configuration."
#elif defined(FRONT_PROBE_BED_POSITION)
#error "FRONT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_FRONT. Please update your configuration."
#elif defined(BACK_PROBE_BED_POSITION)
#error "BACK_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_BACK. Please update your configuration."
#elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
#error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
#elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
#error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
#elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN)
#error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration."
#elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1))
#error "K1 is now PID_K1. Please update your configuration."
#elif defined(PROBE_DOUBLE_TOUCH)
#error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING. Please update your configuration."
#elif defined(ANET_KEYPAD_LCD)
#error "ANET_KEYPAD_LCD is now ZONESTAR_LCD. Please update your configuration."
#elif defined(LCD_I2C_SAINSMART_YWROBOT)
#error "LCD_I2C_SAINSMART_YWROBOT is now LCD_SAINSMART_I2C_(1602|2004). Please update your configuration."
#elif defined(MEASURED_LOWER_LIMIT) || defined(MEASURED_UPPER_LIMIT)
#error "MEASURED_(UPPER|LOWER)_LIMIT is now FILWIDTH_ERROR_MARGIN. Please update your configuration."
#elif defined(HAVE_TMCDRIVER)
#error "HAVE_TMCDRIVER is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(STEALTHCHOP)
#error "STEALTHCHOP is now STEALTHCHOP_(XY|Z|E). Please update your Configuration_adv.h."
#elif defined(HAVE_TMC26X)
#error "HAVE_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(HAVE_TMC2130)
#error "HAVE_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h."
#elif defined(HAVE_TMC2208)
#error "HAVE_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h."
#elif defined(HAVE_L6470DRIVER)
#error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
#elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \
|| defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC)
#error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \
|| defined(E0_IS_TMC26X) || defined(E1_IS_TMC26X) || defined(E2_IS_TMC26X) || defined(E3_IS_TMC26X) || defined(E4_IS_TMC26X) || defined(E5_IS_TMC26X)
#error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \
|| defined(E0_IS_TMC2130) || defined(E1_IS_TMC2130) || defined(E2_IS_TMC2130) || defined(E3_IS_TMC2130) || defined(E4_IS_TMC2130) || defined(E5_IS_TMC2130)
#error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h."
#elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \
|| defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208)
#error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h."
#elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \
|| defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470)
#error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
#elif defined(AUTOMATIC_CURRENT_CONTROL)
#error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
#elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
#error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration."
#elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET)
#error "LEVEL_BED_CORNERS requires a LEVEL_CORNERS_INSET value. Please update your Configuration.h."
#elif defined(BEZIER_JERK_CONTROL)
#error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION. Please update your configuration."
#elif DISABLED(CLASSIC_JERK) && defined(JUNCTION_DEVIATION_FACTOR)
#error "JUNCTION_DEVIATION_FACTOR is now JUNCTION_DEVIATION_MM. Please update your configuration."
#elif defined(JUNCTION_ACCELERATION_FACTOR)
#error "JUNCTION_ACCELERATION_FACTOR is obsolete. Delete it from Configuration_adv.h."
#elif defined(JUNCTION_ACCELERATION)
#error "JUNCTION_ACCELERATION is obsolete. Delete it from Configuration_adv.h."
#elif defined(MAX7219_DEBUG_STEPPER_HEAD)
#error "MAX7219_DEBUG_STEPPER_HEAD is now MAX7219_DEBUG_PLANNER_HEAD. Please update your configuration."
#elif defined(MAX7219_DEBUG_STEPPER_TAIL)
#error "MAX7219_DEBUG_STEPPER_TAIL is now MAX7219_DEBUG_PLANNER_TAIL. Please update your configuration."
#elif defined(MAX7219_DEBUG_STEPPER_QUEUE)
#error "MAX7219_DEBUG_STEPPER_QUEUE is now MAX7219_DEBUG_PLANNER_QUEUE. Please update your configuration."
#elif defined(ENDSTOP_NOISE_FILTER)
#error "ENDSTOP_NOISE_FILTER is now ENDSTOP_NOISE_THRESHOLD [2-7]. Please update your configuration."
#elif defined(RETRACT_ZLIFT)
#error "RETRACT_ZLIFT is now RETRACT_ZRAISE. Please update your Configuration_adv.h."
#elif defined(TOOLCHANGE_PARK_ZLIFT) || defined(TOOLCHANGE_UNPARK_ZLIFT)
#error "TOOLCHANGE_PARK_ZLIFT and TOOLCHANGE_UNPARK_ZLIFT are now TOOLCHANGE_ZRAISE. Please update your configuration."
#elif defined(SINGLENOZZLE_TOOLCHANGE_ZRAISE)
#error "SINGLENOZZLE_TOOLCHANGE_ZRAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
#elif defined(SINGLENOZZLE_SWAP_LENGTH)
#error "SINGLENOZZLE_SWAP_LENGTH is now TOOLCHANGE_FIL_SWAP_LENGTH. Please update your configuration."
#elif defined(SINGLENOZZLE_SWAP_RETRACT_SPEED)
#error "SINGLENOZZLE_SWAP_RETRACT_SPEED is now TOOLCHANGE_FIL_SWAP_RETRACT_SPEED. Please update your configuration."
#elif defined(SINGLENOZZLE_SWAP_PRIME_SPEED)
#error "SINGLENOZZLE_SWAP_PRIME_SPEED is now TOOLCHANGE_FIL_SWAP_PRIME_SPEED. Please update your configuration."
#elif defined(SINGLENOZZLE_SWAP_PARK)
#error "SINGLENOZZLE_SWAP_PARK is now TOOLCHANGE_PARK. Please update your configuration."
#elif defined(SINGLENOZZLE_TOOLCHANGE_XY)
#error "SINGLENOZZLE_TOOLCHANGE_XY is now TOOLCHANGE_PARK_XY. Please update your configuration."
#elif defined(SINGLENOZZLE_PARK_XY_FEEDRATE)
#error "SINGLENOZZLE_PARK_XY_FEEDRATE is now TOOLCHANGE_PARK_XY_FEEDRATE. Please update your configuration."
#elif defined(PARKING_EXTRUDER_SECURITY_RAISE)
#error "PARKING_EXTRUDER_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
#elif defined(SWITCHING_TOOLHEAD_SECURITY_RAISE)
#error "SWITCHING_TOOLHEAD_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
#elif defined(G0_FEEDRATE) && G0_FEEDRATE == 0
#error "G0_FEEDRATE is now used to set the G0 feedrate. Please update your configuration."
#elif defined(MBL_Z_STEP)
#error "MBL_Z_STEP is now MESH_EDIT_Z_STEP. Please update your configuration."
#elif defined(CHDK)
#error "CHDK is now CHDK_PIN. Please update your Configuration_adv.h."
#elif defined(MAX6675_SS)
#error "MAX6675_SS is now MAX6675_SS_PIN. Please update your configuration and/or pins."
#elif defined(MAX6675_SS2)
#error "MAX6675_SS2 is now MAX6675_SS2_PIN. Please update your configuration and/or pins."
#elif defined(SPINDLE_LASER_ENABLE)
#error "SPINDLE_LASER_ENABLE is now SPINDLE_FEATURE or LASER_FEATURE. Please update your Configuration_adv.h."
#elif defined(SPINDLE_LASER_ENABLE_PIN)
#error "SPINDLE_LASER_ENABLE_PIN is now SPINDLE_LASER_ENA_PIN. Please update your Configuration_adv.h and/or pins."
#elif defined(SPINDLE_DIR_CHANGE)
#error "SPINDLE_DIR_CHANGE is now SPINDLE_CHANGE_DIR. Please update your Configuration_adv.h."
#elif defined(SPINDLE_STOP_ON_DIR_CHANGE)
#error "SPINDLE_STOP_ON_DIR_CHANGE is now SPINDLE_CHANGE_DIR_STOP. Please update your Configuration_adv.h."
#elif defined(SPINDLE_LASER_ENABLE_INVERT)
#error "SPINDLE_LASER_ENABLE_INVERT is now SPINDLE_LASER_ACTIVE_HIGH. Please update your Configuration_adv.h."
#elif defined(CHAMBER_HEATER_PIN)
#error "CHAMBER_HEATER_PIN is now HEATER_CHAMBER_PIN. Please update your configuration and/or pins."
#elif defined(TMC_Z_CALIBRATION)
#error "TMC_Z_CALIBRATION has been deprecated in favor of Z_STEPPER_AUTO_ALIGN. Please update your configuration."
#elif defined(Z_MIN_PROBE_ENDSTOP)
#error "Z_MIN_PROBE_ENDSTOP is no longer required. Please remove it from Configuration.h."
#elif defined(DUAL_NOZZLE_DUPLICATION_MODE)
#error "DUAL_NOZZLE_DUPLICATION_MODE is now MULTI_NOZZLE_DUPLICATION. Please update your configuration."
#elif defined(MENU_ITEM_CASE_LIGHT)
#error "MENU_ITEM_CASE_LIGHT is now CASE_LIGHT_MENU. Please update your configuration."
#elif defined(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
#error "ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED is now SD_ABORT_ON_ENDSTOP_HIT. Please update your Configuration_adv.h."
#elif defined(LPC_SD_LCD) || defined(LPC_SD_ONBOARD) || defined(LPC_SD_CUSTOM_CABLE)
#error "LPC_SD_(LCD|ONBOARD|CUSTOM_CABLE) are now SDCARD_CONNECTION. Please update your Configuration_adv.h."
#elif defined(USB_SD_DISABLED)
#error "USB_SD_DISABLED is now NO_SD_HOST_DRIVE. Please update your Configuration_adv.h."
#elif defined(USB_SD_ONBOARD)
#error "USB_SD_ONBOARD is obsolete. Disable NO_SD_HOST_DRIVE instead."
#elif POWER_SUPPLY == 1
#error "Replace POWER_SUPPLY 1 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'false'."
#elif POWER_SUPPLY == 2
#error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'true'."
#elif defined(POWER_SUPPLY)
#error "POWER_SUPPLY is now obsolete. Please remove it from Configuration.h."
#elif defined(MKS_ROBIN_TFT)
#error "MKS_ROBIN_TFT is now FSMC_GRAPHICAL_TFT. Please update your configuration."
#elif defined(SDPOWER)
#error "SDPOWER is now SDPOWER_PIN. Please update your configuration and/or pins."
#elif defined(STRING_SPLASH_LINE1) || defined(STRING_SPLASH_LINE2)
#error "STRING_SPLASH_LINE[12] are now obsolete. Please remove them from Configuration.h."
#elif defined(Z_PROBE_ALLEN_KEY_DEPLOY_1_X) || defined(Z_PROBE_ALLEN_KEY_STOW_1_X)
#error "Z_PROBE_ALLEN_KEY_(DEPLOY|STOW) coordinates are now a single setting. Please update your configuration."
#elif defined(X_PROBE_OFFSET_FROM_EXTRUDER) || defined(Y_PROBE_OFFSET_FROM_EXTRUDER) || defined(Z_PROBE_OFFSET_FROM_EXTRUDER)
#error "[XYZ]_PROBE_OFFSET_FROM_EXTRUDER is now NOZZLE_TO_PROBE_OFFSET. Please update your configuration."
#elif defined(MIN_PROBE_X) || defined(MIN_PROBE_Y) || defined(MAX_PROBE_X) || defined(MAX_PROBE_Y)
#error "(MIN|MAX)_PROBE_[XY] are now calculated at runtime. Please remove them from Configuration.h."
#elif defined(Z_STEPPER_ALIGN_X) || defined(Z_STEPPER_ALIGN_X)
#error "Z_STEPPER_ALIGN_X and Z_STEPPER_ALIGN_Y are now combined as Z_STEPPER_ALIGN_XY. Please update your Configuration_adv.h."
#elif defined(JUNCTION_DEVIATION)
#error "JUNCTION_DEVIATION is no longer required. (See CLASSIC_JERK). Please remove it from Configuration.h."
#endif
#define BOARD_MKS_13 -1000
#define BOARD_TRIGORILLA -1001
#define BOARD_RURAMPS4D -1002
#define BOARD_FORMBOT_TREX2 -1003
#define BOARD_BIQU_SKR_V1_1 -1004
#define BOARD_STM32F1R -1005
#define BOARD_STM32F103R -1006
#if MB(MKS_13)
#error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration."
#elif MB(TRIGORILLA)
#error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration."
#elif MB(RURAMPS4D)
#error "BOARD_RURAMPS4D has been renamed BOARD_RURAMPS4D_11. Please update your configuration."
#elif MB(FORMBOT_TREX2)
#error "FORMBOT_TREX2 has been renamed BOARD_FORMBOT_TREX2PLUS. Please update your configuration."
#elif MB(BIQU_SKR_V1_1)
#error "BOARD_BIQU_SKR_V1_1 has been renamed BOARD_BIGTREE_SKR_V1_1. Please update your configuration."
#elif MB(STM32F1R)
#error "BOARD_STM32F1R has been renamed BOARD_STM32F103RE. Please update your configuration."
#elif MB(STM32F103R)
#error "BOARD_STM32F103R has been renamed BOARD_STM32F103RE. Please update your configuration."
#endif
#undef BOARD_MKS_13
#undef BOARD_TRIGORILLA
#undef BOARD_RURAMPS4D
#undef BOARD_FORMBOT_TREX2
#undef BOARD_BIQU_SKR_V1_1
#undef BOARD_STM32F1R
#undef BOARD_STM32F103R
/**
* Marlin release, version and default string
*/
#ifndef SHORT_BUILD_VERSION
#error "SHORT_BUILD_VERSION must be specified."
#elif !defined(DETAILED_BUILD_VERSION)
#error "BUILD_VERSION must be specified."
#elif !defined(STRING_DISTRIBUTION_DATE)
#error "STRING_DISTRIBUTION_DATE must be specified."
#elif !defined(PROTOCOL_VERSION)
#error "PROTOCOL_VERSION must be specified."
#elif !defined(MACHINE_NAME)
#error "MACHINE_NAME must be specified."
#elif !defined(SOURCE_CODE_URL)
#error "SOURCE_CODE_URL must be specified."
#elif !defined(DEFAULT_MACHINE_UUID)
#error "DEFAULT_MACHINE_UUID must be specified."
#elif !defined(WEBSITE_URL)
#error "WEBSITE_URL must be specified."
#endif
/**
* Serial
*/
#if !(defined(__AVR__) && defined(USBCON))
#if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
#error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops."
#elif RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE))
#error "RX_BUFFER_SIZE must be a power of 2 greater than 1."
#elif TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE))
#error "TX_BUFFER_SIZE must be 0 or a power of 2 between 1 and 256."
#endif
#elif ANY(SERIAL_XON_XOFF, SERIAL_STATS_MAX_RX_QUEUED, SERIAL_STATS_DROPPED_RX)
#error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices."
#endif
#if SERIAL_PORT > 7
#error "Set SERIAL_PORT to the port on your board. Usually this is 0."
#endif
#if defined(SERIAL_PORT_2) && NUM_SERIAL < 2
#error "SERIAL_PORT_2 is not supported for your MOTHERBOARD. Disable it to continue."
#endif
/**
* Dual / Triple Stepper Drivers
*/
#if BOTH(X_DUAL_STEPPER_DRIVERS, DUAL_X_CARRIAGE)
#error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
#elif ENABLED(X_DUAL_STEPPER_DRIVERS) && !(HAS_X2_ENABLE && HAS_X2_STEP && HAS_X2_DIR)
#error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
#elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && !(HAS_Y2_ENABLE && HAS_Y2_STEP && HAS_Y2_DIR)
#error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
#elif ENABLED(Z_DUAL_STEPPER_DRIVERS)
#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS)
#error "Please select either Z_TRIPLE_STEPPER_DRIVERS or Z_DUAL_STEPPER_DRIVERS, not both."
#elif !(HAS_Z2_ENABLE && HAS_Z2_STEP && HAS_Z2_DIR)
#error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
#endif
#elif ENABLED(Z_TRIPLE_STEPPER_DRIVERS) && !(HAS_Z2_ENABLE && HAS_Z2_STEP && HAS_Z2_DIR && HAS_Z3_ENABLE && HAS_Z3_STEP && HAS_Z3_DIR)
#error "Z_TRIPLE_STEPPER_DRIVERS requires Z3 pins (and two extra E plugs)."
#endif
/**
* Validate that the bed size fits
*/
static_assert(X_MAX_LENGTH >= X_BED_SIZE, "Movement bounds (X_MIN_POS, X_MAX_POS) are too narrow to contain X_BED_SIZE.");
static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS) are too narrow to contain Y_BED_SIZE.");
/**
* Granular software endstops (Marlin >= 1.1.7)
*/
#if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z)
#if IS_KINEMATIC
#error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z."
#elif NONE(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y)
#error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options."
#endif
#endif
#if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z)
#if IS_KINEMATIC
#error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z."
#elif NONE(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y)
#error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options."
#endif
#endif
#if !defined(TARGET_LPC1768) && ANY( \
ENDSTOPPULLDOWNS, \
ENDSTOPPULLDOWN_XMAX, ENDSTOPPULLDOWN_YMAX, \
ENDSTOPPULLDOWN_ZMAX, ENDSTOPPULLDOWN_XMIN, \
ENDSTOPPULLDOWN_YMIN, ENDSTOPPULLDOWN_ZMIN \
)
#error "PULLDOWN pin mode is not available on the selected board."
#endif
#if BOTH(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS)
#error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS."
#elif BOTH(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN)
#error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN."
#elif BOTH(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX)
#error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX."
#elif BOTH(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX)
#error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX."
#elif BOTH(ENDSTOPPULLUP_ZMAX, ENDSTOPPULLDOWN_ZMAX)
#error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX."
#elif BOTH(ENDSTOPPULLUP_XMIN, ENDSTOPPULLDOWN_XMIN)
#error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN."
#elif BOTH(ENDSTOPPULLUP_YMIN, ENDSTOPPULLDOWN_YMIN)
#error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN."
#elif BOTH(ENDSTOPPULLUP_ZMIN, ENDSTOPPULLDOWN_ZMIN)
#error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN."
#endif
/**
* LCD Info Screen Style
*/
#if LCD_INFO_SCREEN_STYLE > 0
#if HAS_GRAPHICAL_LCD || LCD_WIDTH < 20 || LCD_HEIGHT < 4
#error "Alternative LCD_INFO_SCREEN_STYLE requires 20x4 Character LCD."
#elif LCD_INFO_SCREEN_STYLE > 1
#error "LCD_INFO_SCREEN_STYLE only has options 0 and 1 at this time."
#endif
#endif
/**
* Progress Bar
*/
#if ENABLED(LCD_PROGRESS_BAR)
#if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
#error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY."
#elif !HAS_CHARACTER_LCD
#error "LCD_PROGRESS_BAR requires a character LCD."
#elif HAS_GRAPHICAL_LCD
#error "LCD_PROGRESS_BAR does not apply to graphical displays."
#elif ENABLED(FILAMENT_LCD_DISPLAY)
#error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
#elif PROGRESS_MSG_EXPIRE < 0
#error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0."
#endif
#elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && !HAS_GRAPHICAL_LCD && DISABLED(EXTENSIBLE_UI)
#error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Graphical LCD, or EXTENSIBLE_UI."
#endif
#if !HAS_LCD_MENU && ENABLED(SD_REPRINT_LAST_SELECTED_FILE)
#error "SD_REPRINT_LAST_SELECTED_FILE currently requires a Marlin-native LCD menu."
#endif
/**
* Custom Boot and Status screens
*/
#if EITHER(SHOW_CUSTOM_BOOTSCREEN, CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_GRAPHICAL_LCD
#error "Graphical LCD is required for SHOW_CUSTOM_BOOTSCREEN and CUSTOM_STATUS_SCREEN_IMAGE."
#endif
/**
* LCD Lightweight Screen Style
*/
#if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920)
#error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display."
#endif
/**
* SD File Sorting
*/
#if ENABLED(SDCARD_SORT_ALPHA)
#if SDSORT_LIMIT > 256
#error "SDSORT_LIMIT must be 256 or smaller."
#elif SDSORT_LIMIT < 10
#error "SDSORT_LIMIT should be greater than 9 to be useful."
#elif DISABLED(SDSORT_USES_RAM)
#if ENABLED(SDSORT_DYNAMIC_RAM)
#error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)."
#elif ENABLED(SDSORT_CACHE_NAMES)
#error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)."
#endif
#endif
#if ENABLED(SDSORT_CACHE_NAMES) && DISABLED(SDSORT_DYNAMIC_RAM)
#if SDSORT_CACHE_VFATS < 2
#error "SDSORT_CACHE_VFATS must be 2 or greater!"
#elif SDSORT_CACHE_VFATS > MAX_VFAT_ENTRIES
#undef SDSORT_CACHE_VFATS
#define SDSORT_CACHE_VFATS MAX_VFAT_ENTRIES
#warning "SDSORT_CACHE_VFATS was reduced to MAX_VFAT_ENTRIES!"
#endif
#endif
#endif
#if defined(EVENT_GCODE_SD_STOP) && DISABLED(NOZZLE_PARK_FEATURE)
static_assert(nullptr == strstr(EVENT_GCODE_SD_STOP, "G27"), "NOZZLE_PARK_FEATURE is required to use G27 in EVENT_GCODE_SD_STOP.");
#endif
/**
* I2C Position Encoders
*/
#if ENABLED(I2C_POSITION_ENCODERS)
#if !BOTH(BABYSTEPPING, BABYSTEP_XY)
#error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY."
#elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5)
#error "I2CPE_ENCODER_CNT must be between 1 and 5."
#endif
#endif
/**
* Babystepping
*/
#if ENABLED(BABYSTEPPING)
#if ENABLED(SCARA)
#error "BABYSTEPPING is not implemented for SCARA yet."
#elif BOTH(DELTA, BABYSTEP_XY)
#error "BABYSTEPPING only implemented for Z axis on deltabots."
#elif BOTH(BABYSTEP_ZPROBE_OFFSET, MESH_BED_LEVELING)
#error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
#elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
#error "BABYSTEP_ZPROBE_OFFSET requires a probe."
#elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_GRAPHICAL_LCD
#error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD."
#elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET)
#error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
#elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET
#error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS."
#elif BOTH(BABYSTEP_ALWAYS_AVAILABLE, MOVE_Z_WHEN_IDLE)
#error "BABYSTEP_ALWAYS_AVAILABLE and MOVE_Z_WHEN_IDLE are incompatible."
#endif
#endif
/**
* Filament Runout needs one or more pins and either SD Support or Auto print start detection
*/
#if HAS_FILAMENT_SENSOR
#if !PIN_EXISTS(FIL_RUNOUT)
#error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
#elif NUM_RUNOUT_SENSORS > E_STEPPERS
#error "NUM_RUNOUT_SENSORS cannot exceed the number of E steppers."
#elif NUM_RUNOUT_SENSORS > 1 && !PIN_EXISTS(FIL_RUNOUT2)
#error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 1 requires FIL_RUNOUT2_PIN."
#elif NUM_RUNOUT_SENSORS > 2 && !PIN_EXISTS(FIL_RUNOUT3)
#error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 2 requires FIL_RUNOUT3_PIN."
#elif NUM_RUNOUT_SENSORS > 3 && !PIN_EXISTS(FIL_RUNOUT4)
#error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 3 requires FIL_RUNOUT4_PIN."
#elif NUM_RUNOUT_SENSORS > 4 && !PIN_EXISTS(FIL_RUNOUT5)
#error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 4 requires FIL_RUNOUT5_PIN."
#elif NUM_RUNOUT_SENSORS > 5 && !PIN_EXISTS(FIL_RUNOUT6)
#error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 5 requires FIL_RUNOUT6_PIN."
#elif NONE(SDSUPPORT, PRINTJOB_TIMER_AUTOSTART)
#error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
#elif FILAMENT_RUNOUT_DISTANCE_MM < 0
#error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero."
#elif DISABLED(ADVANCED_PAUSE_FEATURE)
static_assert(nullptr == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
#endif
#endif
/**
* Advanced Pause
*/
#if ENABLED(ADVANCED_PAUSE_FEATURE)
#if !HAS_RESUME_CONTINUE
#error "ADVANCED_PAUSE_FEATURE currently requires an LCD controller or EMERGENCY_PARSER."
#elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#elif ENABLED(PARK_HEAD_ON_PAUSE) && NONE(SDSUPPORT, NEWPANEL, EMERGENCY_PARSER)
#error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller."
#elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT)
#error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT."
#elif DISABLED(NOZZLE_PARK_FEATURE)
#error "ADVANCED_PAUSE_FEATURE requires NOZZLE_PARK_FEATURE."
#elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_UNLOAD_LENGTH > EXTRUDE_MAXLENGTH
#error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
#elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_SLOW_LOAD_LENGTH > EXTRUDE_MAXLENGTH
#error "FILAMENT_CHANGE_SLOW_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
#elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_FAST_LOAD_LENGTH > EXTRUDE_MAXLENGTH
#error "FILAMENT_CHANGE_FAST_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
#endif
#endif
#if ENABLED(NOZZLE_PARK_FEATURE)
constexpr float npp[] = NOZZLE_PARK_POINT;
static_assert(COUNT(npp) == XYZ, "NOZZLE_PARK_POINT requires X, Y, and Z values.");
#endif
/**
* Individual axis homing is useless for DELTAS
*/
#if BOTH(INDIVIDUAL_AXIS_HOMING_MENU, DELTA)
#error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
#endif
/**
* Options only for EXTRUDERS > 1
*/
#if EXTRUDERS > 1
#if EXTRUDERS > 6
#error "Marlin supports a maximum of 6 EXTRUDERS."
#endif
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
#error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
#endif
#if ENABLED(HEATERS_PARALLEL)
#error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
#endif
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
#ifndef TOOLCHANGE_FIL_SWAP_LENGTH
#error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_LENGTH. Please update your Configuration."
#elif !defined(TOOLCHANGE_FIL_SWAP_RETRACT_SPEED)
#error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_RETRACT_SPEED. Please update your Configuration."
#elif !defined(TOOLCHANGE_FIL_SWAP_PRIME_SPEED)
#error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_PRIME_SPEED. Please update your Configuration."
#endif
#endif
#if ENABLED(TOOLCHANGE_PARK)
#ifndef TOOLCHANGE_PARK_XY
#error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY. Please update your Configuration."
#elif !defined(TOOLCHANGE_PARK_XY_FEEDRATE)
#error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY_FEEDRATE. Please update your Configuration."
#endif
#endif
#ifndef TOOLCHANGE_ZRAISE
#error "TOOLCHANGE_ZRAISE required for EXTRUDERS > 1. Please update your Configuration_adv.h."
#endif
#elif ENABLED(MK2_MULTIPLEXER)
#error "MK2_MULTIPLEXER requires 2 or more EXTRUDERS."
#elif ENABLED(SINGLENOZZLE)
#error "SINGLENOZZLE requires 2 or more EXTRUDERS."
#endif
/**
* Sanity checking for the Průša MK2 Multiplexer
*/
#ifdef SNMM
#error "SNMM is now MK2_MULTIPLEXER. Please update your configuration."
#endif
/**
* A Dual Nozzle carriage with switching servo
*/
#if ENABLED(SWITCHING_NOZZLE)
#if ENABLED(DUAL_X_CARRIAGE)
#error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible."
#elif ENABLED(SINGLENOZZLE)
#error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible."
#elif EXTRUDERS != 2
#error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS."
#elif NUM_SERVOS < 1
#error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1."
#endif
#ifndef SWITCHING_NOZZLE_SERVO_NR
#error "SWITCHING_NOZZLE requires SWITCHING_NOZZLE_SERVO_NR."
#elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
#error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
#error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
#endif
#ifdef SWITCHING_NOZZLE_E1_SERVO_NR
#if SWITCHING_NOZZLE_E1_SERVO_NR == SWITCHING_NOZZLE_SERVO_NR
#error "SWITCHING_NOZZLE_E1_SERVO_NR must be different from SWITCHING_NOZZLE_SERVO_NR."
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
#error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
#error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE."
#elif SWITCHING_NOZZLE_E1_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
#endif
#endif
#endif
/**
* Single Stepper Dual Extruder with switching servo
*/
#if ENABLED(SWITCHING_EXTRUDER)
#if NUM_SERVOS < 1
#error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
#elif SWITCHING_EXTRUDER_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
#error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
#error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER."
#endif
#if EXTRUDERS > 3
#if NUM_SERVOS < 2
#error "SWITCHING_EXTRUDER with 4 extruders requires NUM_SERVOS >= 2."
#elif SWITCHING_EXTRUDER_E23_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
#error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_E23_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
#error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_E23_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
#error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_E23_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
#error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER."
#elif SWITCHING_EXTRUDER_E23_SERVO_NR == SWITCHING_EXTRUDER_SERVO_NR
#error "SWITCHING_EXTRUDER_E23_SERVO_NR should be a different extruder from SWITCHING_EXTRUDER_SERVO_NR."
#endif
#endif
#endif
/**
* Mixing Extruder requirements
*/
#if ENABLED(MIXING_EXTRUDER)
#if EXTRUDERS > 1
#error "For MIXING_EXTRUDER set MIXING_STEPPERS > 1 instead of EXTRUDERS > 1."
#elif MIXING_STEPPERS < 2
#error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
#elif ENABLED(FILAMENT_SENSOR)
#error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
#elif ENABLED(SWITCHING_EXTRUDER)
#error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both."
#elif ENABLED(SINGLENOZZLE)
#error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE."
#endif
#endif
/**
* Linear Advance 1.5 - Check K value range
*/
#if ENABLED(LIN_ADVANCE)
static_assert(
WITHIN(LIN_ADVANCE_K, 0, 10),
"LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)."
);
#endif
/**
* Special tool-changing options
*/
#if 1 < 0 \
+ ENABLED(SINGLENOZZLE) \
+ ENABLED(DUAL_X_CARRIAGE) \
+ ENABLED(PARKING_EXTRUDER) \
+ ENABLED(MAGNETIC_PARKING_EXTRUDER) \
+ ENABLED(SWITCHING_TOOLHEAD) \
+ ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) \
+ ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
#error "Please select only one of SINGLENOZZLE, DUAL_X_CARRIAGE, PARKING_EXTRUDER, SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, or ELECTROMAGNETIC_SWITCHING_TOOLHEAD."
#endif
/**
* (Magnetic) Parking Extruder requirements
*/
#if ANY(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
#if ENABLED(EXT_SOLENOID)
#error "(MAGNETIC_)PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
#elif EXTRUDERS != 2
#error "(MAGNETIC_)PARKING_EXTRUDER requires exactly 2 EXTRUDERS."
#elif !defined(PARKING_EXTRUDER_PARKING_X)
#error "(MAGNETIC_)PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X."
#elif !defined(TOOLCHANGE_ZRAISE)
#error "(MAGNETIC_)PARKING_EXTRUDER requires TOOLCHANGE_ZRAISE."
#elif TOOLCHANGE_ZRAISE < 0
#error "TOOLCHANGE_ZRAISE must be 0 or higher."
#elif ENABLED(PARKING_EXTRUDER)
#if !PIN_EXISTS(SOL0, SOL1)
#error "PARKING_EXTRUDER requires SOL0_PIN and SOL1_PIN."
#elif !defined(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE, LOW, HIGH)
#error "PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE must be defined as HIGH or LOW."
#elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000)
#error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)."
#endif
#endif
#endif
/**
* Switching Toolhead requirements
*/
#if ENABLED(SWITCHING_TOOLHEAD)
#ifndef SWITCHING_TOOLHEAD_SERVO_NR
#error "SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_SERVO_NR."
#elif EXTRUDERS < 2
#error "SWITCHING_TOOLHEAD requires at least 2 EXTRUDERS."
#elif NUM_SERVOS < (SWITCHING_TOOLHEAD_SERVO_NR - 1)
#if SWITCHING_TOOLHEAD_SERVO_NR == 0
#error "A SWITCHING_TOOLHEAD_SERVO_NR of 0 requires NUM_SERVOS >= 1."
#elif SWITCHING_TOOLHEAD_SERVO_NR == 1
#error "A SWITCHING_TOOLHEAD_SERVO_NR of 1 requires NUM_SERVOS >= 2."
#elif SWITCHING_TOOLHEAD_SERVO_NR == 2
#error "A SWITCHING_TOOLHEAD_SERVO_NR of 2 requires NUM_SERVOS >= 3."
#elif SWITCHING_TOOLHEAD_SERVO_NR == 3
#error "A SWITCHING_TOOLHEAD_SERVO_NR of 3 requires NUM_SERVOS >= 4."
#endif
#elif !defined(TOOLCHANGE_ZRAISE)
#error "SWITCHING_TOOLHEAD requires TOOLCHANGE_ZRAISE."
#elif TOOLCHANGE_ZRAISE < 0
#error "TOOLCHANGE_ZRAISE must be 0 or higher."
#endif
#endif
/**
* (Electro)magnetic Switching Toolhead requirements
*/
#if EITHER(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
#ifndef SWITCHING_TOOLHEAD_Y_POS
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_POS"
#elif !defined(SWITCHING_TOOLHEAD_X_POS)
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_X_POS"
#elif !defined(SWITCHING_TOOLHEAD_Z_HOP)
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Z_HOP."
#elif !defined(SWITCHING_TOOLHEAD_Y_CLEAR)
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_CLEAR."
#elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
#if ENABLED(EXT_SOLENOID)
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD and EXT_SOLENOID are incompatible. (Pins are used twice.)"
#elif !PIN_EXISTS(SOL0)
#error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SOL0_PIN."
#endif
#endif
#endif
/**
* Part-Cooling Fan Multiplexer requirements
*/
#if PIN_EXISTS(FANMUX1)
#if !HAS_FANMUX
#error "FANMUX0_PIN must be set before FANMUX1_PIN can be set."
#endif
#elif PIN_EXISTS(FANMUX2)
#error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set."
#endif
/**
* Limited number of servos
*/
#if NUM_SERVOS > NUM_SERVO_PLUGS
#error "The selected board doesn't support enough servos for your configuration. Reduce NUM_SERVOS."
#endif
/**
* Servo deactivation depends on servo endstops, switching nozzle, or switching extruder
*/
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_PROBE && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR) && !defined(SWITCHING_TOOLHEAD_SERVO_NR)
#error "Z_PROBE_SERVO_NR, switching nozzle, switching toolhead or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE."
#endif
/**
* Required LCD language
*/
#if HAS_CHARACTER_LCD && !defined(DISPLAY_CHARSET_HD44780)
#error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
#endif
/**
* Bed Heating Options - PID vs Limit Switching