diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index a946d5198a69..bd1a9485a65f 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -56,7 +56,7 @@
 // #define XY2_V5_220_TITAN_NO_TMC 1
 
 // #define TFT_LVGL_UI
-// #define TFT_CLASSIC_UI
+ // #define TFT_CLASSIC_UI
 // #define TFT_COLOR_UI
 
 #if V6_330_TITAN_TMC
@@ -1570,9 +1570,9 @@
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+  #define FIL_RUNOUT_STATE     HIGH        // Pin state indicating that filament is NOT present.
+  // #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
+  #define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
@@ -1939,7 +1939,7 @@
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 10), 20 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 377e85e34585..03bbf42f2d18 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -2136,7 +2136,7 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
   //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.