-
Notifications
You must be signed in to change notification settings - Fork 190
Troubleshooting
This page summarizes what you should try when facing performance or stability issues.
If your situation does not improve by trying the solutions here, or if you cannot find the cause of your issue, it may be an issue on Synology's side (USB xHCI host controller hardware or its driver). In that case, there is no solution at this time.
Reports from other users may be helpful in guessing whether the problem is on the Synology side.
Front ports tend to be more stable, but some users have reported they got better stability with rear ports
In some environments, the power supply of USB ports may be insufficient. It causes forcing the device into the slow/low-power mode or stopping.
For example, the following products would be good.
-
SABRENT 4-Port USB 3.0 Hub with Individual LED Lit Power Switches, Includes 5V/2.5A Power Adapter (HB-UMP3)
- Examples of symptoms improved by this product: #1
- ANRANK USB 3.0 Female to Dual USB Male Extra Power Data Extension Cord Adapter Splitter Y-Cable Black
Synology's USB ports are sensitive to noise, so you should not use these accessories even if they are of acceptable quality for PC use.
Some dongles have a USB Type-C port and are shipped with a Type-C to Type-A converter cable, but some of these cables may result in a USB 2.0 connection if the wrong side is used.
Ethernet devices tend to be sensitive to other USB devices in terms of communication characteristics and power consumption.
If the device is unstable, disconnect other USB devices to isolate the problem and see what happens.
Some switches sometimes fail to auto-negotiate the Multi-Giga link or may cause compatibility issues with the SFP transceiver module. Connecting without a Switch eliminates this possibility.
Your NIC, switch, or router may have a newer version of firmware or drivers than the version that came with it when it shipped. Also, the version available on the vendor's page is often newer than the version distributed via Windows Update.
- Marvell(Aquantia) Drivers & Firmwares
- QNAP Download Center
- Realtek Drivers
- Intel® Network Adapter Driver for Windows® 10
- TP-Link Download Center
- MikroTik Software Downloads
- ASUS - How to update the firmware
The aqc111u has a feature that automatically drops the link speed when the chip gets high temperatures. This feature is enabled by default and should be left enabled as much as possible, but you may want to disable it to isolate the cause of the problem. In that case, execute the following command on the terminal and then Stop&Run the driver from the Package Center.
echo off | sudo tee /var/packages/aqc111/etc/flag-thermal_throttling
Category 5e/6/6A cables are required in a Multi-Giga environment. Category 6A is recommended for longer(> 3m) cables. Category 7/8 cables are almost a SCAM and should not be used.
Also, changes in hardware configuration may surface quality problems that the cable originally had. If you are using an old cable, I recommend trying a new cable.
In the balance of quality and cost, I personally recommend the following products:
- Cat6A Ethernet Patch Cable by Monoprice
- Cat6 Ethernet Patch Cable by Ubiquiti Networks
You can confirm the protocol version of your device using by lsusb command.
|__1-3 1c04:0015:0101 00 2.10 480MBit/s 500mA 1IF (QNAP QNAP QNA-UC5G1T USB to 5GbE Adapter 2BI03114)
For example, 2.10 480MBit/s indicates that the device using USB 2(480Mbps). In this situation, sufficient speed cannot be obtained.
To use USB 3, change the connection port (blue ports are USB 3) or change the USB cable. (if the cable is detachable)
When USB 3 is used, 3.20 5000MBit/s will appear as shown below.
|__2-1 1c04:0015:0101 00 3.20 5000MBit/s 896mA 1IF (QNAP QNAP QNA-UC5G1T USB to 5GbE Adapter 2BI03114)
USB transactions consume a lot of CPU power and have a high overhead. Transmitting more data in a single packet at a time may reduce this overhead and improve performance.
In addition to the driver and physical layer, performance degradation can also be caused by the protocol layer (e.g., SMB) and server software. It is important to measure performance at the pure TCP/IP level to isolate these.
The iperf for Synology can be easily installed from SynoCommunity.
If the file transfer rate to and from Windows is slow, try setting the SMB protocol version set to a higher version.
Also please note that if you are using a larger MTU, the version should be set to SMB2 and Large MTU or SMB3.
All Ethernet devices have an auto-negotiation mechanism that automatically determines the link speed, but this mechanism can sometimes cause unstable operation due to interoperability issues between devices. This happens more often in a Multi-Giga environment.
To check whether auto-negotiation works correctly, use the ethtool command.
Settings for eth2:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 5000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
If ethtool does not report the expected link speed, disable auto-negotiation by explicitly specifying the link speed.
For example, to disable auto-negotiation and fix the link speed to 1gbps, do the following.
sudo ethtool -s eth2 speed 1000 duplex full autoneg off
When you connect the device to the PC directly or your switch has the feature to fix link speed, it would be better to specify link speeds on those opposing devices.
The above command cannot be used to operate the 2.5gbps link for the r8152 driver. Use the following commands.
sudo ethtool -s eth2 autoneg on advertise 0x802f
Some transceivers link up at 2.5Gbps/5Gbps even though they do not support MultiGiga (IEEE 802.3bz). While these products may appear to work, they do not provide enough performance.
So carefully check the vendor's page for specifications and information about the combination with your switch.
Starting with version 1.3.3.0-6, low power mode is enabled by default in favor of stability.
To disable it, execute the following command on the terminal and then Stop&Run the driver from the Package Center.
echo on | sudo tee /var/packages/aqc111/etc/flag-low_power_5g
For more information on the RX ring buffer, see the explanation page by RedHat.
Show Ring parameter
sudo ethtool -g eth2
Changes the number of ring entries for the Rx ring.
sudo ethtool -G eth2 rx 100