kvm: vmx: Flush TLB when the APIC-access address changes

Quoting from the Intel SDM, volume 3, section 28.3.3.4: Guidelines for
Use of the INVEPT Instruction:

If EPT was in use on a logical processor at one time with EPTP X, it
is recommended that software use the INVEPT instruction with the
"single-context" INVEPT type and with EPTP X in the INVEPT descriptor
before a VM entry on the same logical processor that enables EPT with
EPTP X and either (a) the "virtualize APIC accesses" VM-execution
control was changed from 0 to 1; or (b) the value of the APIC-access
address was changed.

In the nested case, the burden falls on L1, unless L0 enables EPT in
vmcs02 when L1 doesn't enable EPT in vmcs12.

Signed-off-by: Jim Mattson <[email protected]>
Signed-off-by: Radim Krčmář <[email protected]>

arch/x86/kvm/vmx.c

@@ -4024,6 +4024,12 @@ static void vmx_flush_tlb(struct kvm_vcpu *vcpu)
 	__vmx_flush_tlb(vcpu, to_vmx(vcpu)->vpid);
 }
 
+static void vmx_flush_tlb_ept_only(struct kvm_vcpu *vcpu)
+{
+	if (enable_ept)
+		vmx_flush_tlb(vcpu);
+}
+
 static void vmx_decache_cr0_guest_bits(struct kvm_vcpu *vcpu)
 {
 	ulong cr0_guest_owned_bits = vcpu->arch.cr0_guest_owned_bits;
@@ -8548,6 +8554,7 @@ static void vmx_set_virtual_x2apic_mode(struct kvm_vcpu *vcpu, bool set)
 	} else {
 		sec_exec_control &= ~SECONDARY_EXEC_VIRTUALIZE_X2APIC_MODE;
 		sec_exec_control |= SECONDARY_EXEC_VIRTUALIZE_APIC_ACCESSES;
+		vmx_flush_tlb_ept_only(vcpu);
 	}
 	vmcs_write32(SECONDARY_VM_EXEC_CONTROL, sec_exec_control);
 
@@ -8573,8 +8580,10 @@ static void vmx_set_apic_access_page_addr(struct kvm_vcpu *vcpu, hpa_t hpa)
 	 */
 	if (!is_guest_mode(vcpu) ||
 	    !nested_cpu_has2(get_vmcs12(&vmx->vcpu),
-			     SECONDARY_EXEC_VIRTUALIZE_APIC_ACCESSES))
+			     SECONDARY_EXEC_VIRTUALIZE_APIC_ACCESSES)) {
 		vmcs_write64(APIC_ACCESS_ADDR, hpa);
+		vmx_flush_tlb_ept_only(vcpu);
+	}
 }
 
 static void vmx_hwapic_isr_update(struct kvm_vcpu *vcpu, int max_isr)
@@ -10256,6 +10265,9 @@ static int prepare_vmcs02(struct kvm_vcpu *vcpu, struct vmcs12 *vmcs12,
 	if (nested_cpu_has_ept(vmcs12)) {
 		kvm_mmu_unload(vcpu);
 		nested_ept_init_mmu_context(vcpu);
+	} else if (nested_cpu_has2(vmcs12,
+				   SECONDARY_EXEC_VIRTUALIZE_APIC_ACCESSES)) {
+		vmx_flush_tlb_ept_only(vcpu);
 	}
 
 	/*
@@ -11055,6 +11067,10 @@ static void nested_vmx_vmexit(struct kvm_vcpu *vcpu, u32 exit_reason,
 		vmx->nested.change_vmcs01_virtual_x2apic_mode = false;
 		vmx_set_virtual_x2apic_mode(vcpu,
 				vcpu->arch.apic_base & X2APIC_ENABLE);
+	} else if (!nested_cpu_has_ept(vmcs12) &&
+		   nested_cpu_has2(vmcs12,
+				   SECONDARY_EXEC_VIRTUALIZE_APIC_ACCESSES)) {
+		vmx_flush_tlb_ept_only(vcpu);
 	}
 
 	/* This is needed for same reason as it was needed in prepare_vmcs02 */