-
Notifications
You must be signed in to change notification settings - Fork 20
/
zuluscsi.ini
101 lines (83 loc) · 4.9 KB
/
zuluscsi.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
# See http://zuluscsi.com/manual for more information about setting up your ZuluSCSI
[SCSI]
# Settings that apply to all SCSI IDs
# Select a system preset to apply default settings
# Known systems: "Mac", "MacPlus", "MPC3000", "MegaSTE", "X68000"
#System="Mac"
#Debug = 0 # Same effect as DIPSW2, enables verbose log messages
#DebugLogMask = 255 # A bit mask for SCSI IDs 0-7, filters only matching SCSI ID debug messages
#DebugIgnoreBusyFree = 0 # Set to 1 to ignore the BUS_FREE and BUS_BUSY logging
#SelectionDelay = 255 # Millisecond delay after selection, 255 = automatic, 0 = no delay
#Dir = "/" # Optionally look for image files in subdirectory
#Dir2 = "/images" # Multiple directories can be specified Dir1...Dir9
#DisableStatusLED = 1 # 0: Use status LED, 1: Disable status LED
#EnableToolbox = 1 # Enable Toolbox API. Disabled by default for compatibility reasons.
# NOTE: PhyMode is only relevant for ZuluSCSI V1.1 at this time.
#PhyMode = 0 # 0: Best available 1: PIO 2: DMA_TIMER 3: GREENPAK_PIO 4: GREENPAK_DMA
# The PhyMode parameter has no effect on ZuluSCSI RP2040-based platforms, as there is only one PHY mode.
# Settings that can be needed for compatibility with some hosts
#Quirks = 0 # 0: Standard, 1: Apple, 2: OMTI, 4: Xebec, 8: VMS, 16: X68000, 32: EWSD
#EnableUnitAttention = 0 # Post UNIT_ATTENTION status on power-on or SD card hotplug
#EnableSCSI2 = 1 # Enable faster speeds of SCSI2
#EnableSelLatch = 0 # For Philips P2000C and other devices that release SEL signal before BSY
#EnableParity = 1 # Enable parity checks on platforms that support it (RP2040)
#MapLunsToIDs = 0 # For Philips P2000C simulate multiple LUNs
#InitPreDelay = 0 # How many milliseconds to delay before the SCSI interface is initialized
#InitPostDelay = 0 # How many milliseconds to delay after the SCSI interface is initialized
# Will attempt to reclock the board if the board supports both reclocking and the choosen speed
# SpeedGrade = Default # TurboMax - max speed, TurboA - mode A, TurboC, etc
# When reclocking the board MaxSyncSpeed may need to be increased, see manual for details
# MaxSyncSpeed = 10 # Set to 5, 10, or 20 to enable synchronous SCSI mode, 0 to disable
# ROM settings
#DisableROMDrive = 1 # Disable the ROM drive if it has been loaded to flash
#ROMDriveSCSIID = 7 # Override ROM drive's SCSI ID
#Initiator settings
#InitiatorID = 7 # SCSI ID, 0-7, when the device is in initiator mode, default is 7
#InitiatorMaxRetry = 5 # number of retries on failed reads 0-255, default is 5
#InitiatorImageHandling = 0 # 0: skip existing images, 1: create new image with incrementing suffix, 2: overwrite existing image
#EnableCDAudio = 0 # 1: Enable CD audio - an external I2S DAC on the v1.2 is required
# Settings that can be specified either per-device or for all devices.
# Select a device preset to apply default settings
# Known systems: "ST32430N"
#Device = "ST32430N"
#Vendor = "QUANTUM"
#Product = "FIREBALL1"
#Version = "1.0"
#Serial = "0123456789ABCDEF"
#Type = 0 # 0: Fixed, 1: Removable, 2: Optical, 3: Floppy, 4: Mag-optical,
# 5: Tape, 6: Network, 7: Zip100
#VendorExtensions = 0 # Bit flags for specific extensions per device type
# CDROM - 1: Plextor's d8h vendor command
#TypeModifier = 0 # Affects only INQUIRY response
#SectorsPerTrack = 63
#HeadsPerCylinder = 255
#RightAlignStrings = 0 # Right-align SCSI vendor / product strings
#PrefetchBytes = 8192 # Maximum number of bytes to prefetch after a read request, 0 to disable
#ReinsertCDOnInquiry = 1 # Reinsert any ejected CD-ROM image on Inquiry command
#ReinsertAfterEject = 1 # Reinsert next CD image after eject, if multiple images configured.
#EjectButton = 0 # Enable eject by button 1 or 2, or set 0 to disable
#CDAVolume = 63 # Change CD Audio default volume. Maximum 255.
#DisableMacSanityCheck = 0 # Disable sanity warnings for Mac disk drives. Default is 0 - enable checks
#BlockSize = 0 # Set the drive's blocksize, defaults to 2048 for CDs and 512 for all other drives
# Mount SD card as a mass storage device before entering SCSI emulator
# EnableUSBMassStorage = 1 # setting this to one will mount the SD card if the USB cord is plugged in
# USBMassStorageWaitPeriod = 1000 # Number of milliseconds the device will wait for the host to mount SD card
# May need to be increased if connected through a USB hub
# SCSI DaynaPORT settings
#WiFiSSID = "Wifi SSID string"
#WiFiPassword = "WiFi Password"
#WiFiMACAddress = "01:23:45:67:89"
# Settings can be overridden for individual devices.
#[SCSI2]
#Product = "Disk with ID2"
#[SCSI5]
#Product = "CD-ROM Drive"
#Type = 2
# If IMG0..IMG9 are specified, they are cycled after each eject command.
#IMG0 = FirstCD.iso
#IMG1 = SecondCD.bin
# Raw sector range from SD card can be passed through
# Format is RAW:first_sector:last_sector where sector numbers can be decimal or hex.
# If end sector is beyond end of SD card, it will be adjusted automatically.
# [SCSI4]
# IMG0 = RAW:0x00000000:0xFFFFFFFF # Whole SD card