FINAL.ino

#include <Adafruit_GPS.h>
#include <SPI.h>
#include <Wire.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_LSM9DS0.h>


/* Assign a unique base ID for this sensor */   
Adafruit_LSM9DS0 lsm = Adafruit_LSM9DS0(1000);  // Use I2C, ID #1000


/* Or, use Hardware SPI:
  SCK -> SPI CLK
  SDA -> SPI MOSI
  G_SDO + XM_SDO -> tied together to SPI MISO
  then select any two pins for the two CS lines:
*/

#define LSM9DS0_XM_CS 10
#define LSM9DS0_GYRO_CS 9
//Adafruit_LSM9DS0 lsm = Adafruit_LSM9DS0(LSM9DS0_XM_CS, LSM9DS0_GYRO_CS, 1000);

/* Or, use Software SPI:
  G_SDO + XM_SDO -> tied together to the MISO pin!
  then select any pins for the SPI lines, and the two CS pins above
*/

#define LSM9DS0_SCLK 13
#define LSM9DS0_MISO 12
#define LSM9DS0_MOSI 11

//Adafruit_LSM9DS0 lsm = Adafruit_LSM9DS0(LSM9DS0_SCLK, LSM9DS0_MISO, LSM9DS0_MOSI, LSM9DS0_XM_CS, LSM9DS0_GYRO_CS, 1000);

// what's the name of the hardware serial port?
#define GPSSerial Serial1

// Connect to the GPS on the hardware port
Adafruit_GPS GPS(&GPSSerial);
     
// Set GPSECHO to 'false' to turn off echoing the GPS data to the Serial console
// Set to 'true' if you want to debug and listen to the raw GPS sentences
#define GPSECHO false

uint32_t timer = millis();


void setup()
{
  //while (!Serial);  // uncomment to have the sketch wait until Serial is ready
  
  // connect at 115200 so we can read the GPS fast enough and echo without dropping chars
  // also spit it out
  Serial.begin(115200);
  Serial.println("Adafruit GPS library basic test!");
     
  // 9600 NMEA is the default baud rate for Adafruit MTK GPS's- some use 4800
  GPS.begin(9600);
  // uncomment this line to turn on RMC (recommended minimum) and GGA (fix data) including altitude
  GPS.sendCommand(PMTK_SET_NMEA_OUTPUT_RMCGGA);
  // uncomment this line to turn on only the "minimum recommended" data
  //GPS.sendCommand(PMTK_SET_NMEA_OUTPUT_RMCONLY);
  // For parsing data, we don't suggest using anything but either RMC only or RMC+GGA since
  // the parser doesn't care about other sentences at this time
  // Set the update rate
  GPS.sendCommand(PMTK_SET_NMEA_UPDATE_1HZ); // 1 Hz update rate
  // For the parsing code to work nicely and have time to sort thru the data, and
  // print it out we don't suggest using anything higher than 1 Hz
     
  // Request updates on antenna status, comment out to keep quiet
  GPS.sendCommand(PGCMD_ANTENNA);

  delay(1000);
  
  // Ask for firmware version
  GPSSerial.println(PMTK_Q_RELEASE);

  #ifndef ESP8266
  while (!Serial);     // will pause Zero, Leonardo, etc until serial console opens
#endif
  Serial.begin(9600);
  Serial.println(F("LSM9DS0 9DOF Sensor Test")); Serial.println("");
  
  /* Initialise the sensor */
  if(!lsm.begin())
  {
    /* There was a problem detecting the LSM9DS0 ... check your connections */
    Serial.print(F("Ooops, no LSM9DS0 detected ... Check your wiring or I2C ADDR!"));
    while(1);
  }
  Serial.println(F("Found LSM9DS0 9DOF"));
  
  /* Display some basic information on this sensor */
  displaySensorDetails();
  
  /* Setup the sensor gain and integration time */
  configureSensor();
  
  /* We're ready to go! */
  Serial.println("");
}

void loop() // run over and over again
{
  // read data from the GPS in the 'main loop'
  char c = GPS.read();
  // if you want to debug, this is a good time to do it!
  if (GPSECHO)
    if (c) Serial.print(c);
  // if a sentence is received, we can check the checksum, parse it...
  if (GPS.newNMEAreceived()) {
    // a tricky thing here is if we print the NMEA sentence, or data
    // we end up not listening and catching other sentences!
    // so be very wary if using OUTPUT_ALLDATA and trytng to print out data
    Serial.println(GPS.lastNMEA()); // this also sets the newNMEAreceived() flag to false
    if (!GPS.parse(GPS.lastNMEA())) // this also sets the newNMEAreceived() flag to false
      return; // we can fail to parse a sentence in which case we should just wait for another
  }
  // if millis() or timer wraps around, we'll just reset it
  if (timer > millis()) timer = millis();
     
  // approximately every 2 seconds or so, print out the current stats
  if (millis() - timer > 2000) {
    timer = millis(); // reset the timer
    Serial.print("\nTime: ");
    Serial.print(GPS.hour, DEC); Serial.print(':');
    Serial.print(GPS.minute, DEC); Serial.print(':');
    Serial.print(GPS.seconds, DEC); Serial.print('.');
    Serial.println(GPS.milliseconds);
    Serial.print("Date: ");
    Serial.print(GPS.day, DEC); Serial.print('/');
    Serial.print(GPS.month, DEC); Serial.print("/20");
    Serial.println(GPS.year, DEC);
    Serial.print("Fix: "); Serial.print((int)GPS.fix);
    Serial.print(" quality: "); Serial.println((int)GPS.fixquality);
    if (GPS.fix) {
      Serial.print("Location: ");
      Serial.print(GPS.latitude, 4); Serial.print(GPS.lat);
      Serial.print(", ");
      Serial.print(GPS.longitude, 4); Serial.println(GPS.lon);
      Serial.print("Speed (knots): "); Serial.println(GPS.speed);
      Serial.print("Angle: "); Serial.println(GPS.angle);
      Serial.print("Altitude: "); Serial.println(GPS.altitude);
      Serial.print("Satellites: "); Serial.println((int)GPS.satellites);

      /* Get a new sensor event */ 
  sensors_event_t accel, mag, gyro, temp;

  lsm.getEvent(&accel, &mag, &gyro, &temp); 

  // print out accelleration data
  Serial.print("Accel X: "); Serial.print(accel.acceleration.x); Serial.print(" ");
  Serial.print("  \tY: "); Serial.print(accel.acceleration.y);       Serial.print(" ");
  Serial.print("  \tZ: "); Serial.print(accel.acceleration.z);     Serial.println("  \tm/s^2");

  // print out magnetometer data
  Serial.print("Magn. X: "); Serial.print(mag.magnetic.x); Serial.print(" ");
  Serial.print("  \tY: "); Serial.print(mag.magnetic.y);       Serial.print(" ");
  Serial.print("  \tZ: "); Serial.print(mag.magnetic.z);     Serial.println("  \tgauss");
  
  // print out gyroscopic data
  Serial.print("Gyro  X: "); Serial.print(gyro.gyro.x); Serial.print(" ");
  Serial.print("  \tY: "); Serial.print(gyro.gyro.y);       Serial.print(" ");
  Serial.print("  \tZ: "); Serial.print(gyro.gyro.z);     Serial.println("  \tdps");

  // print out temperature data
  Serial.print("Temp: "); Serial.print(temp.temperature); Serial.println(" *C");

  Serial.println("**********************\n");

  delay(2000);
    }
  }
}


/* This driver uses the Adafruit unified sensor library (Adafruit_Sensor),
   which provides a common 'type' for sensor data and some helper functions.
   
   To use this driver you will also need to download the Adafruit_Sensor
   library and include it in your libraries folder.

   You should also assign a unique ID to this sensor for use with
   the Adafruit Sensor API so that you can identify this particular
   sensor in any data logs, etc.  To assign a unique ID, simply
   provide an appropriate value in the constructor below (12345
   is used by default in this example).
   
   Connections (For default I2C)
   ===========
   Connect SCL to analog 5
   Connect SDA to analog 4
   Connect VDD to 5V DC
   Connect GROUND to common ground

   History
   =======
   2014/JULY/25  - First version (KTOWN)
*/
   


/**************************************************************************/
/*
    Displays some basic information on this sensor from the unified
    sensor API sensor_t type (see Adafruit_Sensor for more information)
*/
/**************************************************************************/
void displaySensorDetails(void)
{
  sensor_t accel, mag, gyro, temp;
  
  lsm.getSensor(&accel, &mag, &gyro, &temp);
  
  Serial.println(F("------------------------------------"));
  Serial.print  (F("Sensor:       ")); Serial.println(accel.name);
  Serial.print  (F("Driver Ver:   ")); Serial.println(accel.version);
  Serial.print  (F("Unique ID:    ")); Serial.println(accel.sensor_id);
  Serial.print  (F("Max Value:    ")); Serial.print(accel.max_value); Serial.println(F(" m/s^2"));
  Serial.print  (F("Min Value:    ")); Serial.print(accel.min_value); Serial.println(F(" m/s^2"));
  Serial.print  (F("Resolution:   ")); Serial.print(accel.resolution); Serial.println(F(" m/s^2"));  
  Serial.println(F("------------------------------------"));
  Serial.println(F(""));

  Serial.println(F("------------------------------------"));
  Serial.print  (F("Sensor:       ")); Serial.println(mag.name);
  Serial.print  (F("Driver Ver:   ")); Serial.println(mag.version);
  Serial.print  (F("Unique ID:    ")); Serial.println(mag.sensor_id);
  Serial.print  (F("Max Value:    ")); Serial.print(mag.max_value); Serial.println(F(" uT"));
  Serial.print  (F("Min Value:    ")); Serial.print(mag.min_value); Serial.println(F(" uT"));
  Serial.print  (F("Resolution:   ")); Serial.print(mag.resolution); Serial.println(F(" uT"));  
  Serial.println(F("------------------------------------"));
  Serial.println(F(""));

  Serial.println(F("------------------------------------"));
  Serial.print  (F("Sensor:       ")); Serial.println(gyro.name);
  Serial.print  (F("Driver Ver:   ")); Serial.println(gyro.version);
  Serial.print  (F("Unique ID:    ")); Serial.println(gyro.sensor_id);
  Serial.print  (F("Max Value:    ")); Serial.print(gyro.max_value); Serial.println(F(" rad/s"));
  Serial.print  (F("Min Value:    ")); Serial.print(gyro.min_value); Serial.println(F(" rad/s"));
  Serial.print  (F("Resolution:   ")); Serial.print(gyro.resolution); Serial.println(F(" rad/s"));  
  Serial.println(F("------------------------------------"));
  Serial.println(F(""));

  Serial.println(F("------------------------------------"));
  Serial.print  (F("Sensor:       ")); Serial.println(temp.name);
  Serial.print  (F("Driver Ver:   ")); Serial.println(temp.version);
  Serial.print  (F("Unique ID:    ")); Serial.println(temp.sensor_id);
  Serial.print  (F("Max Value:    ")); Serial.print(temp.max_value); Serial.println(F(" C"));
  Serial.print  (F("Min Value:    ")); Serial.print(temp.min_value); Serial.println(F(" C"));
  Serial.print  (F("Resolution:   ")); Serial.print(temp.resolution); Serial.println(F(" C"));  
  Serial.println(F("------------------------------------"));
  Serial.println(F(""));
  
  delay(1500);
}

/**************************************************************************/
/*
    Configures the gain and integration time for the TSL2561
*/
/**************************************************************************/
void configureSensor(void)
{
  // 1.) Set the accelerometer range
  lsm.setupAccel(lsm.LSM9DS0_ACCELRANGE_2G);
  //lsm.setupAccel(lsm.LSM9DS0_ACCELRANGE_4G);
  //lsm.setupAccel(lsm.LSM9DS0_ACCELRANGE_6G);
  //lsm.setupAccel(lsm.LSM9DS0_ACCELRANGE_8G);
  //lsm.setupAccel(lsm.LSM9DS0_ACCELRANGE_16G);
  
  // 2.) Set the magnetometer sensitivity
  lsm.setupMag(lsm.LSM9DS0_MAGGAIN_2GAUSS);
  //lsm.setupMag(lsm.LSM9DS0_MAGGAIN_4GAUSS);
  //lsm.setupMag(lsm.LSM9DS0_MAGGAIN_8GAUSS);
  //lsm.setupMag(lsm.LSM9DS0_MAGGAIN_12GAUSS);

  // 3.) Setup the gyroscope
  lsm.setupGyro(lsm.LSM9DS0_GYROSCALE_245DPS);
  //lsm.setupGyro(lsm.LSM9DS0_GYROSCALE_500DPS);
  //lsm.setupGyro(lsm.LSM9DS0_GYROSCALE_2000DPS);
}