forked from Klipper3d/klipper
-
Notifications
You must be signed in to change notification settings - Fork 15
/
printer-adimlab-2018.cfg
123 lines (108 loc) · 2.1 KB
/
printer-adimlab-2018.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
# This file contains pin mappings for the ADIMLab 3d printer 2018.
# To use this config, the firmware should be compiled for the AVR atmega2560.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PA3
dir_pin: !PA1
enable_pin: !PA5
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PA0
position_min: -5
position_endstop: -5
position_max: 310
homing_speed: 30.0
[stepper_y]
step_pin: PC5
dir_pin: !PC4
enable_pin: !PC6
microsteps: 16
rotation_distance: 40
endstop_pin: ^!PA4
position_endstop: 0
position_max: 310
homing_speed: 30.0
[stepper_z]
step_pin: PC2
dir_pin: PC1
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: ^!PA7
position_endstop: 0.0
position_max: 400
homing_speed: 5.0
[extruder]
step_pin: PL7
dir_pin: PL6
enable_pin: !PC0
microsteps: 16
rotation_distance: 34.557
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PE4
sensor_type: ATC Semitec 104GT-2
sensor_pin: PK0
control: pid
pid_Kp: 15.717
pid_Ki: 0.569
pid_Kd: 108.451
min_temp: 0
max_temp: 245
[heater_bed]
heater_pin: PG5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK2
control: pid
pid_Kp: 74.883
pid_Ki: 1.809
pid_Kd: 775.038
min_temp: 0
max_temp: 110
[verify_heater heater_bed]
# adjust for personal bed setup, this prevents stock heated bed from issuing
# false positive heating errors due to slow temperature increase
# 1 deg per 2 minutes.
heating_gain: 1
check_gain_time: 120
[mcu]
serial: /dev/ttyUSB0
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 10
max_z_accel: 60
[output_pin stepper_xy_current]
pin: PL5
pwm: True
scale: 2.0
cycle_time: .000030
hardware_pwm: True
static_value: 1.3
[output_pin stepper_z_current]
pin: PL4
pwm: True
scale: 2.0
cycle_time: .000030
hardware_pwm: True
static_value: 1.3
[output_pin stepper_e_current]
pin: PL3
pwm: True
scale: 2.0
cycle_time: .000030
hardware_pwm: True
static_value: 1.25
[display]
lcd_type: st7920
cs_pin: PD1
sclk_pin: PJ1
sid_pin: PJ0
encoder_pins: ^PG0, ^PG1
click_pin: ^!PD2
# The filament runout sensor (on pin PA2) is not currently supported
# in Klipper.
[output_pin case_light]
pin: PH4
value: 1