g2c3g

\mainpage Main Page

---

G2C 3G Click

Go to Cloud (G2C) 3G Click is a gateway Click board™ which provides a simple and reliable connection to the Click Cloud platform, a cloud-based rapid prototyping environment, hosted by Mikroe. G2C 3G offers an unprecedented simplicity for adding Click Cloud connectivity over UMTS/HSPA to any embedded application, by utilizing the simple UART interface: it can be configured and managed using a minimal set of well-documented AT commands.

Click Product page

---

Click library

• Author : Stefan Filipovic
• Date : May 2023.
• Type : UART type

Software Support

We provide a library for the G2C 3G Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for G2C 3G Click driver.

Standard key functions :

• g2c3g_cfg_setup Config Object Initialization function.

void g2c3g_cfg_setup ( g2c3g_cfg_t *cfg );

• g2c3g_init Initialization function.

err_t g2c3g_init ( g2c3g_t *ctx, g2c3g_cfg_t *cfg );

Example key functions :

• g2c3g_reset_device This function resets the device by toggling the RST pin.

void g2c3g_reset_device ( g2c3g_t *ctx );

• g2c3g_set_net_creds This function sets the APN, username, and password for entered sim card.

void g2c3g_set_net_creds ( g2c3g_t *ctx, uint8_t *sim_apn, uint8_t *username, uint8_t *password );

• g2c3g_set_broker_creds This function sets the broker credentials (device key and password).

void g2c3g_set_broker_creds ( g2c3g_t *ctx, uint8_t *dev_key, uint8_t *password );

Example Description

This example shows the device capability of connecting to the cloud and updating the sensor data on the cloud and receiving data from actuators.

The demo application is composed of two sections :

Application Init

Initializes the driver, restarts the device, and after that tests the communication by sending "AT" command.

void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    g2c3g_cfg_t g2c3g_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    g2c3g_cfg_setup( &g2c3g_cfg );
    G2C3G_MAP_MIKROBUS( g2c3g_cfg, MIKROBUS_2 );
    if ( UART_ERROR == g2c3g_init( &g2c3g, &g2c3g_cfg ) ) 
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }

    // Clear RX buffer
    g2c3g_process( );   
    g2c3g_clear_app_buf( );
    Delay_ms ( 100 );
    
    // Reset device
    g2c3g_reset_device ( &g2c3g );
    error_flag = g2c3g_rsp_check( G2C3G_RSP_DEVICE_READY );
    g2c3g_error_check( error_flag );
    
    // Check communication
    g2c3g_send_cmd( &g2c3g, G2C3G_CMD_AT );
    error_flag = g2c3g_rsp_check( G2C3G_RSP_OK );
    g2c3g_error_check( error_flag );
    
    log_info( &logger, " Application Task " );
    example_state = G2C3G_CONNECT_TO_NETWORK;
}

Application Task

Application task is split in few stages:

• G2C3G_CONNECT_TO_NETWORK:

  Sends commands to configure device to connect to the specified network.

• G2C3G_CONNECT_TO_CLOUD:

  Sends commands to configure device to connect to the specified device on the cloud.

• G2C3G_EXAMPLE:

  This function executes example which updates sensor data on the cloud and displays all data received from the module (ex. the actuator switch state change received from the cloud).

void application_task ( void )
{
    switch ( example_state )
    {
        case G2C3G_CONNECT_TO_NETWORK:
        {
            if ( G2C3G_OK == g2c3g_connect_to_network( ) )
            {
                example_state = G2C3G_CONNECT_TO_CLOUD;
            }
            break;
        }
        case G2C3G_CONNECT_TO_CLOUD:
        {
            if ( G2C3G_OK == g2c3g_connect_to_cloud( ) )
            {
                example_state = G2C3G_EXAMPLE;
            }
            break;
        }
        case G2C3G_EXAMPLE:
        {
            g2c3g_example( );
            break;
        }
        default:
        {
            log_error( &logger, " Example state." );
            break;
        }
    }
}

Note

In order for the example to work, user needs to set the SIM card and the cloud device parameters. Enter valid values for the following macros: SIM_APN, SIM_USERNAME, SIM_PASSWORD, DEVICE_KEY, DEVICE_PASSWORD, DEVICE_SENSOR_REF.

Example:

• SIM_APN "internet"
• SIM_USERNAME "internet"
• SIM_PASSWORD "internet"
• DEVICE_KEY "xxxxxxxxxxxxxxxx"
• DEVICE_PASSWORD "xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx"
• DEVICE_SENSOR_REF "TEMP_SEN_R" DEVICE_KEY and DEVICE_PASSWORD strings should match the device credentials which were generated during the Click Cloud device creation step. DEVICE_SENSOR_REF is expected to be a reference to a temperature sensor with a data range from -20 to +80 degrees Celsius. For more information about the registration on the Click Cloud and creating the device refer to the following user guide.

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.G2C3G

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

---