diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index bd402afcbc4..12813a687cd 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 53e26ed7cfa..a7647522e2e 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index 6841fdeb6ae..8af80e797de 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 28 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index 994ec624c34..0359107123b 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index a058ebbdb15..c81e03c7e74 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index c303dc986ee..fe60e19b585 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -1266,7 +1266,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1278,6 +1277,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index f6be830cbcc..d8bb716520b 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index e0dde420e87..ef60d79b8a6 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index b90425680d4..909b876bb76 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index b90425680d4..909b876bb76 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 6fd6443eecd..7c8fffff378 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index bbbf8d84395..da491428be2 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 816cce302af..9bd4a3c7870 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/A9/Configuration_adv.h b/config/examples/Anet/A9/Configuration_adv.h index 5a2bbde9021..1154d2d43d6 100644 --- a/config/examples/Anet/A9/Configuration_adv.h +++ b/config/examples/Anet/A9/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index ad6bb57b82f..3711f1c74d2 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h index 91aecdfbdcd..4baacda4f6f 100644 --- a/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h +++ b/config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/E16/Stock/Configuration_adv.h b/config/examples/Anet/E16/Stock/Configuration_adv.h index 9c1b43d79e9..5b84ce814cd 100644 --- a/config/examples/Anet/E16/Stock/Configuration_adv.h +++ b/config/examples/Anet/E16/Stock/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET4+/Configuration_adv.h b/config/examples/Anet/ET4+/Configuration_adv.h index e037403977f..109a6009df7 100644 --- a/config/examples/Anet/ET4+/Configuration_adv.h +++ b/config/examples/Anet/ET4+/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET4-Pro/Configuration_adv.h b/config/examples/Anet/ET4-Pro/Configuration_adv.h index e037403977f..109a6009df7 100644 --- a/config/examples/Anet/ET4-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET4-Pro/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET4/Configuration_adv.h b/config/examples/Anet/ET4/Configuration_adv.h index aa2571e73c5..4aa677fcc75 100644 --- a/config/examples/Anet/ET4/Configuration_adv.h +++ b/config/examples/Anet/ET4/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET4X/Configuration_adv.h b/config/examples/Anet/ET4X/Configuration_adv.h index aa2571e73c5..4aa677fcc75 100644 --- a/config/examples/Anet/ET4X/Configuration_adv.h +++ b/config/examples/Anet/ET4X/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET5-Pro/Configuration_adv.h b/config/examples/Anet/ET5-Pro/Configuration_adv.h index b6eadbab037..fec21350dfc 100644 --- a/config/examples/Anet/ET5-Pro/Configuration_adv.h +++ b/config/examples/Anet/ET5-Pro/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET5/Configuration_adv.h b/config/examples/Anet/ET5/Configuration_adv.h index b6eadbab037..fec21350dfc 100644 --- a/config/examples/Anet/ET5/Configuration_adv.h +++ b/config/examples/Anet/ET5/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Anet/ET5X/Configuration_adv.h b/config/examples/Anet/ET5X/Configuration_adv.h index b6eadbab037..fec21350dfc 100644 --- a/config/examples/Anet/ET5X/Configuration_adv.h +++ b/config/examples/Anet/ET5X/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AnyCubic/Chiron/Configuration_adv.h b/config/examples/AnyCubic/Chiron/Configuration_adv.h index 8236fee1509..ae847002b46 100644 --- a/config/examples/AnyCubic/Chiron/Configuration_adv.h +++ b/config/examples/AnyCubic/Chiron/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - #define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 79 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + #define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h index cfe050ff130..3def247885f 100644 --- a/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h index 146735ba497..ffd6f37f722 100644 --- a/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h +++ b/config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h index 3bab7fb04c3..c349236c99a 100644 --- a/config/examples/AnyCubic/i3 Mega/Configuration_adv.h +++ b/config/examples/AnyCubic/i3 Mega/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 84bb21a5434..b969b45ae53 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index 21361935815..6db5d4ae912 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -1260,7 +1260,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1272,6 +1271,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index d37ac3b9049..75065e94ae6 100644 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index d37ac3b9049..75065e94ae6 100644 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h index 8e983be933e..bff67bd2f6e 100644 --- a/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1_0.9_degree_BMG_E3D_V6/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Azteeg/X5GT/Configuration_adv.h b/config/examples/Azteeg/X5GT/Configuration_adv.h index d1ef8e1f9f1..d33d313cad6 100644 --- a/config/examples/Azteeg/X5GT/Configuration_adv.h +++ b/config/examples/Azteeg/X5GT/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index bc1f0df0f85..432d62eea80 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 2f625c49e55..0db1d05bdb4 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -1249,7 +1249,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1261,6 +1260,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h index 4f08a8945e4..c40b5511b6f 100644 --- a/config/examples/BIQU/B1-BLTouch/Configuration_adv.h +++ b/config/examples/BIQU/B1-BLTouch/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BIQU/B1/Configuration_adv.h b/config/examples/BIQU/B1/Configuration_adv.h index 4d86272652b..f647500b39b 100644 --- a/config/examples/BIQU/B1/Configuration_adv.h +++ b/config/examples/BIQU/B1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index cc27813abfe..9df540835f2 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 73c9ed0d2e7..7fb066c8b17 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -1264,7 +1264,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1276,6 +1275,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index cc27813abfe..9df540835f2 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 0cb15bb035a..ac4ddca80a9 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h index 7bb6b5471f9..e676953a0d3 100644 --- a/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h index 0f18ddf7cb6..101ed6f2f26 100644 --- a/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h index eae25ff65a0..0e80b634dbb 100644 --- a/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h index eae25ff65a0..0e80b634dbb 100644 --- a/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10 V2/Configuration_adv.h b/config/examples/Creality/CR-10 V2/Configuration_adv.h index 759ef5f6b1c..6aa47d00332 100644 --- a/config/examples/Creality/CR-10 V2/Configuration_adv.h +++ b/config/examples/Creality/CR-10 V2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 5b92f9ea389..6b3bcafdc3d 100644 --- a/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h index 2c2f8dfb798..7b28dde99dd 100644 --- a/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h index 1059f02fffe..e59ac6fbc2d 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index a0e57688a88..a8b572f906f 100644 --- a/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h index f1f41c96eaa..341b09608dc 100644 --- a/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 7196677bd67..c340ac0b77c 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index a2f9b51e6c6..75fb278eaca 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-6 SE/Configuration_adv.h b/config/examples/Creality/CR-6 SE/Configuration_adv.h index 721dc3b9794..53a26f61bb8 100644 --- a/config/examples/Creality/CR-6 SE/Configuration_adv.h +++ b/config/examples/Creality/CR-6 SE/Configuration_adv.h @@ -1257,7 +1257,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1269,6 +1268,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index ce5279b6d26..6695f0ec68b 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 2f4e7fcbf96..03a025846a6 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 912046abe50..7121cfcb046 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index eb7078f3719..e12de92c198 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index a8b9fe66c8b..dfd3052f1a5 100644 --- a/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h index 2d0f45b6275..78fe877731b 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h index 2facf8d70d9..95f127d3d85 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV422/Configuration_adv.h @@ -1257,7 +1257,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1269,6 +1268,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h index b40275e5d45..fc631b63984 100644 --- a/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 Pro/CrealityV427/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3 V2/Configuration_adv.h b/config/examples/Creality/Ender-3 V2/Configuration_adv.h index a34a7ee0022..e858e34a3ac 100644 --- a/config/examples/Creality/Ender-3 V2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3 V2/Configuration_adv.h @@ -1257,7 +1257,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1269,6 +1268,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h index 62d1966d459..3eea71fb11c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/2-into-1 Hotend/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h index d49cc449b7f..7e626ed2197 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Dual Z/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h index 62d1966d459..3eea71fb11c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3 Turbo/Single Extruder/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h index 7bd59ef45d5..10574303fe8 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR E3-DIP V1.1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h index 8e1f67f05e9..89cb3f3f83b 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 5565e1417c8..3babc4fd345 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 826228e32b4..e6d8cbb7c7c 100644 --- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h index 46936267e2b..47bd280e6ea 100644 --- a/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h index 46936267e2b..47bd280e6ea 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h index 40304a0d5b1..b71d061c105 100644 --- a/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV427/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h index 67246f95906..5ebbf45d7dd 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/BLTouch/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h index 67246f95906..5ebbf45d7dd 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah 1.2/base/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h index 67246f95906..5ebbf45d7dd 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/BLTouch/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h index 67246f95906..5ebbf45d7dd 100644 --- a/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/FYSETC Cheetah/base/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h index aa1ff686610..a51ea556eb8 100644 --- a/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MEEB-3DP/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h index 32691c484ef..b435885e486 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3 1.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h index 1cb733a3a1b..e8cbbcf4235 100644 --- a/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/MKS Robin E3P/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index b0850c428c6..5caae4e86cf 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h index 3ca13be016a..8944e14bb79 100644 --- a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h index 345461f1a1a..74b8149900c 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h index c483fc870df..b195535269f 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 05be3b8c69c..bf417cdefc3 100644 --- a/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h index 3e3473b4800..5f9883f1548 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h index 02d241acc58..c05f83699cc 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h index 3e3473b4800..5f9883f1548 100644 --- a/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/CrealityV427/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h index 2a2085282fa..21f78472057 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration_adv.h @@ -1260,7 +1260,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1272,6 +1271,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h index 345461f1a1a..74b8149900c 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo with BLTouch/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h index c483fc870df..b195535269f 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR E3 Turbo/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h index 114e4bfe880..f1c6d0c9f0d 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h index 5546512d25e..360dfcde1f1 100644 --- a/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h index fa07b2667db..edf27652f2f 100644 --- a/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h index fa07b2667db..edf27652f2f 100644 --- a/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/CrealityV427/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Creality/Ender-6/Configuration_adv.h b/config/examples/Creality/Ender-6/Configuration_adv.h index ba62e01eeca..ce54aa749a7 100644 --- a/config/examples/Creality/Ender-6/Configuration_adv.h +++ b/config/examples/Creality/Ender-6/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 63570fa1f51..a549ed46887 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Daycom/3DP-100/Configuration_adv.h b/config/examples/Daycom/3DP-100/Configuration_adv.h index 33cd0576573..7f0b9149550 100644 --- a/config/examples/Daycom/3DP-100/Configuration_adv.h +++ b/config/examples/Daycom/3DP-100/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index 117d614737e..a07d80dfb0a 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 46a58856144..d668815a877 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Eryone/Thinker SE/Thinker V2 board/stock/Configuration_adv.h b/config/examples/Eryone/Thinker SE/Thinker V2 board/stock/Configuration_adv.h index 3b2059797a7..7bc415652eb 100644 --- a/config/examples/Eryone/Thinker SE/Thinker V2 board/stock/Configuration_adv.h +++ b/config/examples/Eryone/Thinker SE/Thinker V2 board/stock/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index 898f31574d8..cb566aea787 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index e3f8f503387..1491e908278 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index 62f9e149cac..bad8fff9f9c 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index 35802e6cf1b..c3ef0b3e513 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index 35802e6cf1b..c3ef0b3e513 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FlashForge/Creator 2X/Configuration_adv.h b/config/examples/FlashForge/Creator 2X/Configuration_adv.h index a79ff78ad92..2a79e9a3325 100644 --- a/config/examples/FlashForge/Creator 2X/Configuration_adv.h +++ b/config/examples/FlashForge/Creator 2X/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 66c234abf94..b995809a230 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -1255,7 +1255,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1267,6 +1266,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FlyingBear/P905H/Configuration_adv.h b/config/examples/FlyingBear/P905H/Configuration_adv.h index b28b6ad6631..73b842679db 100644 --- a/config/examples/FlyingBear/P905H/Configuration_adv.h +++ b/config/examples/FlyingBear/P905H/Configuration_adv.h @@ -1259,7 +1259,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1271,6 +1270,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 08259a022cf..f0a3406a155 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index f88f2a36eaa..48540206214 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index b92756cad0b..0c35691fa31 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index b4850af4f01..b69794590c6 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -1260,7 +1260,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1272,6 +1271,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 977bec255e5..d920a86618a 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index cd8d2214914..42a7c7d8cad 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 8d8b28f9ce1..85366870c79 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index 8d8b28f9ce1..85366870c79 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index c218bd13f8d..b2fde7e664a 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index c218bd13f8d..b2fde7e664a 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index c218bd13f8d..b2fde7e664a 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 69 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 6974683299c..01b66659a06 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 4bc18d31a6d..0fd9501493d 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/Duplicator5/Configuration_adv.h b/config/examples/Geeetech/Duplicator5/Configuration_adv.h index 62f9e149cac..bad8fff9f9c 100644 --- a/config/examples/Geeetech/Duplicator5/Configuration_adv.h +++ b/config/examples/Geeetech/Duplicator5/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 6974683299c..01b66659a06 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 4bc18d31a6d..0fd9501493d 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index f8eea978ec9..065a5851af2 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/Me_creator/Configuration_adv.h b/config/examples/Geeetech/Me_creator/Configuration_adv.h index 62f9e149cac..bad8fff9f9c 100644 --- a/config/examples/Geeetech/Me_creator/Configuration_adv.h +++ b/config/examples/Geeetech/Me_creator/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/Me_ducer/Configuration_adv.h b/config/examples/Geeetech/Me_ducer/Configuration_adv.h index d71abbfe933..f3ecec449bd 100644 --- a/config/examples/Geeetech/Me_ducer/Configuration_adv.h +++ b/config/examples/Geeetech/Me_ducer/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index f2a98d129f0..2e5592fe38a 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 977bec255e5..d920a86618a 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 977bec255e5..d920a86618a 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index 5278a35ce04..03df70fc817 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -1247,7 +1247,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1259,6 +1258,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index b0b38601086..681e15e2beb 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h index f6999962982..6316dd9d7b0 100644 --- a/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h +++ b/config/examples/Intamsys/FunmatHT 4988/Configuration_adv.h @@ -1255,7 +1255,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1267,6 +1266,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 95ccedd869d..b06100c6341 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -1261,7 +1261,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1273,6 +1272,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index f9588f3a7f3..96588fdd625 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 95ccedd869d..b06100c6341 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -1261,7 +1261,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1273,6 +1272,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 93b3bb051fa..899ae6d1924 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Kingroon/KP3/Configuration_adv.h b/config/examples/Kingroon/KP3/Configuration_adv.h index 90099d15798..bedf2bdc18b 100644 --- a/config/examples/Kingroon/KP3/Configuration_adv.h +++ b/config/examples/Kingroon/KP3/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Labists/ET4/Configuration_adv.h b/config/examples/Labists/ET4/Configuration_adv.h index e037403977f..109a6009df7 100644 --- a/config/examples/Labists/ET4/Configuration_adv.h +++ b/config/examples/Labists/ET4/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/MBot/Cube/Configuration_adv.h b/config/examples/MBot/Cube/Configuration_adv.h index f8fa89f6d0e..98233536a80 100644 --- a/config/examples/MBot/Cube/Configuration_adv.h +++ b/config/examples/MBot/Cube/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h index 9472210f980..7dfa936a11a 100644 --- a/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus 12/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 9856f80cc59..4f54ace0df4 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 7ee57e4f660..2b1e134f6b9 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 72d5d15e2d0..211b4f2c341 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 9185ea64f3b..208250e1511 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index d1ef8e1f9f1..d33d313cad6 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index a1169905be0..aaa7735c3b4 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 493b1b124b6..27cebf9aa81 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Ortur 4/Configuration_adv.h b/config/examples/Ortur 4/Configuration_adv.h index c16a7aba9c9..7fd943323f8 100644 --- a/config/examples/Ortur 4/Configuration_adv.h +++ b/config/examples/Ortur 4/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 64 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h index 997fd6057e9..aa09c9a4275 100644 --- a/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h +++ b/config/examples/Prusa/MK3S-BigTreeTech-BTT002/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Qidi/Qidi 1/Configuration_adv.h b/config/examples/Qidi/Qidi 1/Configuration_adv.h index 94668e54e7a..e14c8a7d289 100644 --- a/config/examples/Qidi/Qidi 1/Configuration_adv.h +++ b/config/examples/Qidi/Qidi 1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Raiscube/A8r/Configuration_adv.h b/config/examples/Raiscube/A8r/Configuration_adv.h index 6fd6443eecd..7c8fffff378 100644 --- a/config/examples/Raiscube/A8r/Configuration_adv.h +++ b/config/examples/Raiscube/A8r/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index ed453b0ed84..b1b29c298a7 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 6a8e5f7a86d..2433278f26d 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 6a8e5f7a86d..2433278f26d 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 6a8e5f7a86d..2433278f26d 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 898328eead4..e39ae47f7ce 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index d4891aa4d3d..660aa60c3c5 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -1253,7 +1253,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1265,6 +1264,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index b30fd67920d..2d4f1c1391e 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -1253,7 +1253,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1265,6 +1264,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 2cba001fb9d..69299016dfc 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 8e32f7cc739..1349f960539 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Sovol/SV-01/Configuration_adv.h b/config/examples/Sovol/SV-01/Configuration_adv.h index 0aeee6fd82a..247ccb73e6b 100644 --- a/config/examples/Sovol/SV-01/Configuration_adv.h +++ b/config/examples/Sovol/SV-01/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 2.00 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index e71e4f4397d..27121d36a7f 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index baff576d9d3..a2c82c6704a 100644 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 16e3f0f0f43..01a8710415a 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 5497afd30f5..45d76fe6c53 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 5497afd30f5..45d76fe6c53 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index cb756229f76..0c27bdfcada 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 8949d23eecd..2229604de4d 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 631c3b8b941..c079dce8cad 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index 38e698a4ca4..9d55ee9e838 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Tronxy/X5SA/Configuration_adv.h b/config/examples/Tronxy/X5SA/Configuration_adv.h index e62dd9f92cc..e603badc056 100644 --- a/config/examples/Tronxy/X5SA/Configuration_adv.h +++ b/config/examples/Tronxy/X5SA/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h index 5ee47c23098..7c792d8049a 100644 --- a/config/examples/Two Trees/BlueR Plus/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR Plus/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h index 33e9ca2bd4e..7cae47ace8f 100644 --- a/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h index 33e9ca2bd4e..7cae47ace8f 100644 --- a/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h index 33e9ca2bd4e..7cae47ace8f 100644 --- a/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h +++ b/config/examples/Two Trees/BlueR/BlueR V3/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h index 3e441be5894..789aa3d72c4 100644 --- a/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Plus/Sapphire Plus V2/Configuration_adv.h @@ -1262,7 +1262,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1274,6 +1273,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h index d8ce4c5c57a..9a6ece23531 100644 --- a/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h +++ b/config/examples/Two Trees/Sapphire Pro/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 6ddbaa4a597..0952551f0c7 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index f886f5034c6..1c2b3132f65 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 088be1000ac..a744241d999 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index b83892fa78d..e04d8a0bae2 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -1269,7 +1269,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1281,6 +1280,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index 8162912909e..7e529ce5f6f 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index 8162912909e..7e529ce5f6f 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 66293d131bd..a4c4c02c6ec 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN 65 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h index fab0796496b..4c2d7525666 100644 --- a/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 4S/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 573c48bfbd9..8be167d86e3 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index ec13f65a792..2f607e8459e 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index 618e4df8fdc..dcc1815f06b 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Weistek/wt150/Configuration_adv.h b/config/examples/Weistek/wt150/Configuration_adv.h index e1b615bdb6b..7766df23604 100644 --- a/config/examples/Weistek/wt150/Configuration_adv.h +++ b/config/examples/Weistek/wt150/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Zonestar/P802M/Configuration_adv.h b/config/examples/Zonestar/P802M/Configuration_adv.h index 5891535f21b..d9de3a7ddb3 100644 --- a/config/examples/Zonestar/P802M/Configuration_adv.h +++ b/config/examples/Zonestar/P802M/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h index ea5b3c25c71..f37f5121cd4 100755 --- a/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h +++ b/config/examples/Zonestar/P802QR2/BigTreeTech SKR 1.4 Turbo (A4988)/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h index 5bd5334e991..9914e84dd8e 100644 --- a/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel Linear Plus/Configuration_adv.h @@ -1259,7 +1259,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1271,6 +1270,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 2c4441918ff..a2d9d2e9190 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Anycubic/Predator/Configuration_adv.h b/config/examples/delta/Anycubic/Predator/Configuration_adv.h index e38e2a8761b..3f0fb0e6f83 100644 --- a/config/examples/delta/Anycubic/Predator/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Predator/Configuration_adv.h @@ -1259,7 +1259,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1271,6 +1270,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index d6c20d97faa..df82645f806 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 318963cb196..0da2528aaac 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index e39a3e13dd0..1f262ecdbed 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h index 2b566546fa7..297df2f90cc 100644 --- a/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQS-Pro/Configuration_adv.h @@ -1259,7 +1259,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) #define POWER_LOSS_PIN -1 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1271,6 +1270,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index ceaf750d118..aba374b58f3 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index ceaf750d118..aba374b58f3 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index fa5ad236458..a3e8eff19e0 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Geeetech/G2/Configuration_adv.h b/config/examples/delta/Geeetech/G2/Configuration_adv.h index c9677d55195..125f2dfa82e 100644 --- a/config/examples/delta/Geeetech/G2/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h index ac79b0bf96d..f089bdb8f11 100644 --- a/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2Pro/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Geeetech/G2S/Configuration_adv.h b/config/examples/delta/Geeetech/G2S/Configuration_adv.h index ac79b0bf96d..f089bdb8f11 100644 --- a/config/examples/delta/Geeetech/G2S/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2S/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h index ac79b0bf96d..f089bdb8f11 100644 --- a/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h +++ b/config/examples/delta/Geeetech/G2SPro/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index bc47da89a37..f4b72ad5a2c 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h index 82fc23493e1..1bde4b25436 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 2c4d06e5841..06000c45e40 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Malyan M300/Configuration_adv.h b/config/examples/delta/Malyan M300/Configuration_adv.h index 8b1b08f8092..456bfba31f4 100644 --- a/config/examples/delta/Malyan M300/Configuration_adv.h +++ b/config/examples/delta/Malyan M300/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 9f8fecdffd4..0b1625c58d5 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index fa5ad236458..a3e8eff19e0 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 5e6d5ecffb0..a513c65c5c6 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 7df667fae0f..20542dbbffd 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -1258,7 +1258,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1270,6 +1269,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index e279fb48f6d..b1b0b1ce524 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 49b6ce6443d..285d73254eb 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /** diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index a52ced4b5fb..de32cb9fc32 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -1256,7 +1256,6 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss - //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss @@ -1268,6 +1267,12 @@ // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // especially with "vase mode" printing. Set too high and vases cannot be continued. #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + // Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled! + //#define POWER_LOSS_RECOVER_ZHOME + #if ENABLED(POWER_LOSS_RECOVER_ZHOME) + //#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed + #endif #endif /**