1.9inch_ESP32-1732S019 NOT WORK

[taoloo897]

HI. I tried to use T_eSPI with 1.9inch_ESP32-1732S019 with ST7789 but doesn't work. I use this library with T-HMI ESP32-S3 Touch Display 2.8 inch ST7789 and it works GREATE.
I make it works with Arduino_GFX_Library.h but it is hard to work with it in the code.
This is the board
https://www.aliexpress.com/item/1005005951347460.html?spm=a2g0o.order_list.order_list_main.13.21ef1802v1yiy9
If you can add it in your library will be awsome.
Thanks in advance.

[Bodmer]

The display should work.

Post your setup file.

Run Read_User_Setup sketch and post the serial monitor output here.

[taoloo897]

Hi and thanks for your answer.
I have a big problem with serial monitor. I tried a lot of examples before wrote here and nou tried Reqad_User_Setup , but it is very strange , i don;t receive anything on serial only
18:11:49.230 -> ESP-ROM:esp32s3-20210327
18:11:49.230 -> Build:Mar 27 2021
18:11:49.230 -> rst:0x1 (POWERON),boot:0xb (SPI_FAST_FLASH_BOOT)
18:11:49.230 -> SPIWP:0xee
18:11:49.230 -> mode:DIO, clock div:1
18:11:49.230 -> load:0x3fce3808,len:0x44c
18:11:49.230 -> load:0x403c9700,len:0xbd8
18:11:49.230 -> load:0x403cc700,len:0x2a80
18:11:49.230 -> entry 0x403c98d0
The baudrate is ok and i use configuration of board like in attached picture.

All what i upload from Arduino IDE not send message on serial monitor. Only if i upload the bin from vendor example with flash_download_tool_3.9.3 , than it send on serial.
Thanks again for your time.

[Bodmer]

Did you set the baud rate correctly to 115200?

[taoloo897]

Yes the baud rate is correct setted. i tried all baud from 9660 to 500000. It was from this enabled settings USB CDC on boot (strange because for lilygo esp32-s3 t-hmi 2.8 must enabled it) . I disabled it for this bord. I got the serial, but looks strange too , because is i run the same code with for lilygo esp32-s3 t-hmi 2.8 they show the same things on the serial like next:
08:30:22.741 -> [code]
08:30:22.741 -> TFT_eSPI ver = 2.5.23
08:30:22.741 -> Processor = ESP32
08:30:22.741 -> Frequency = 240MHz
08:30:22.741 -> Transactions = Yes
08:30:22.741 -> Interface = Parallel
08:30:22.741 -> Display driver = 7789
08:30:22.741 -> Display width = 240
08:30:22.741 -> Display height = 320
08:30:22.741 ->
08:30:22.741 -> TFT_CS = GPIO 6
08:30:22.741 -> TFT_DC = GPIO 7
08:30:22.741 -> TFT_WR = GPIO 8
08:30:22.741 ->
08:30:22.741 -> TFT_D0 = GPIO 48
08:30:22.741 -> TFT_D1 = GPIO 47
08:30:22.741 -> TFT_D2 = GPIO 39
08:30:22.741 -> TFT_D3 = GPIO 40
08:30:22.741 -> TFT_D4 = GPIO 41
08:30:22.741 -> TFT_D5 = GPIO 42
08:30:22.776 -> TFT_D6 = GPIO 45
08:30:22.776 -> TFT_D7 = GPIO 46
08:30:22.776 ->
08:30:22.776 -> TFT_BL = GPIO 38
08:30:22.776 ->
08:30:22.776 -> Font GLCD loaded
08:30:22.776 -> Font 2 loaded
08:30:22.776 -> Font 4 loaded
08:30:22.776 -> Font 6 loaded
08:30:22.776 -> Font 7 loaded
08:30:22.776 -> Font 8 loaded
08:30:22.776 -> Smooth font enabled

[Bodmer]

The library is not configured correctly for the SPI display.

Edit User_Setup_Select.h to point to one suitable setup file, maybe setup 206. You will need to adjust the pins used in that setup file as it is for a different board.

[taoloo897]

With 206 setup i receive these:
4:51:45.687 -> [code]
14:51:45.687 -> TFT_eSPI ver = 2.5.23
14:51:45.687 -> Processor = ESP32
14:51:45.687 -> Frequency = 240MHz
14:51:45.687 -> Transactions = Yes
14:51:45.687 -> Interface = Parallel
14:51:45.687 -> Display driver = 7789
14:51:45.687 -> Display width = 170
14:51:45.687 -> Display height = 320
14:51:45.687 ->
14:51:45.687 -> R0 x offset = 35
14:51:45.719 -> TFT_DC = GPIO 7
14:51:45.719 -> TFT_RST = GPIO 5
14:51:45.719 -> TFT_WR = GPIO 8
14:51:45.719 -> TFT_RD = GPIO 9
14:51:45.719 ->
14:51:45.719 -> TFT_D0 = GPIO 39
14:51:45.719 -> TFT_D1 = GPIO 40
14:51:45.719 -> TFT_D2 = GPIO 41
14:51:45.719 -> TFT_D3 = GPIO 42
14:51:45.719 -> TFT_D4 = GPIO 45
14:51:45.719 -> TFT_D5 = GPIO 46
14:51:45.719 -> TFT_D6 = GPIO 47
14:51:45.719 -> TFT_D7 = GPIO 48
14:51:45.719 ->
14:51:45.719 -> TFT_BL = GPIO 38
14:51:45.719 -> TFT_BACKLIGHT_ON = HIGH
14:51:45.719 ->
14:51:45.719 -> Font GLCD loaded
14:51:45.719 -> Font 2 loaded
14:51:45.719 -> Font 4 loaded
14:51:45.752 -> Font 6 loaded
14:51:45.752 -> Font 7 loaded
14:51:45.752 -> Font 8 loaded
14:51:45.752 -> Smooth font enabled
But if i tried any example from tft_eSpi library , nothing show on display.
For lilygo esp32-s3 t-hmi 2.8 " every time i must put in setup next lines because without them the display not open. Maybe i must have something like this for 1.9" board but what pins??
pinMode(10, OUTPUT);
digitalWrite(10, HIGH);

[taoloo897]

Try again please.
I made it work but if i use button with some attachclick it reboot if i try to draw strings or numbers in some places, but maybe it is from my code.
Setup72_ESP32_ST7789_172x320.zip

[Bodmer]

Yes, that is good. Thanks.

[Consoli93]

Could you provide me with the files? I can't do it
esp32-1732S019

[sardor1122]

Hello everyone, I was able to make it work, here is the link to the library
https://github.com/moononournation/Arduino_GFX
And this is ino file
sketch_aug25a.zip